WORK DESCRIPTION FOR FIELD MEASURE
Code: 20P3293022
Version: 2.0
Check seal bellows at wheel carrier supporting joint of left and right rear axle, replace if necessary
Model 205; 253
Check/test procedure
- Lift vehicle on vehicle lift and check both seal bellows (A, figure 1) of supporting joint in left and right wheel carrier for damage. The test shall be performed on the right and left wheel carrier.
Figure 1 (Shown on right side)
-
- Visible damage present: Perform work procedure.
- Visible damage not present: End measure.
Work procedure
Only if visible damage is present.
1. Replace affected supporting joint.
For basic data, see AR35.20-P-0116LW.
Perform wheel alignment check.
Parts
| Quantity | Designation | Part no. |
| As required* | Joint | A 204 352 00 27 |
* The bolts and nuts must be determined according to the equipment variant for the vehicle identification number via the parts process in the Xentry Portal!
Small parts such as screws/bolts, lock nuts, sealing rings, cable ties, fluids, sealant etc. are not listed in the parts list. The required small parts are taken into account in the budgeting.
Operation text and flat rate
| Operation no. | Operation text | Flat rate | Accounting no./ damage code |
| 02-1675 | Check seal bellows at outer bearing of supporting joint for left and right spring link of rear axle | 0.1 hours | 32 930 22 |
| 02-1676 * | Replace outer bearing of supporting joint for spring link of rear axle (after check) | 1.6 hours | 32 930 22 |
| 02-1677 | Extra work for: Replace outer bearing of supporting joint for spring link of rear axle in veh. with AIRMATIC | 0.2 hours | 32 930 22 |
| 02-9785 | Operations: Perform wheel alignment check | 0.9 hours | 32 930 22 |
* The operation item is to be repeated as often as necessary.
Mercedes-Benz
Global Service & Parts
Check Seal Bellows at Wheel Carrier
Model GLC-Class (253 platform)
Model Year 2020
SaleBestseller No. 1
OMT Ball Joint Press Kit, Ball Joint Removal Tool with 4x4 Adapters
- ESSENTIAL TOOL FOR BALL JOINT SERVICE - Use the ORION MOTOR TECH Ball Joint Press Set Ball Joint Tool / Bushing Removal Tool with 4WD Adapter to effortlessly remove press fit parts including ball joints, U-joints, brake anchor pins, and more on most 2-wheel drive (2WD) and 4-wheel drive (4WD) vehicles without removing the control arm from the vehicle.
- PROFESSIONAL GRADE QUALITY AND DURABILITY - Off road weekend warriors, novices, and professional mechanics trust the ORION kit because ORION MOTOR TECH sources the highest quality components from around the world. Constructed from heavy-duty forged steel with black-oxide finish on adapters for maximum strength and longevity that resists rust and corrosion.
- UNIVERSALLY COMPATIBLE WITH A WIDE RANGE OF VEHICLES - Fit most American domestic and imported 2-wheel drive (2WD) and 4-wheel drive (4WD) cars and light pickup trucks that have press-fit type ball joints, include 4-wheel drive (4WD) adapter that allows service for 1967 thru current 1/2 and 3/4 ton 4WD vehicles having the Dana 30 or 44 front axle (found on Ford, GM, Dodge, IHC and Jeep vehicles).
- CONVENIENTLY ORGANIZED IN CUSTOM MOLDED CASE - Ball joint press / bushing/ removal tool kit is enclosed inside a heavy-duty 11” x 3” x 15” inch (27.9cm x 7.6cm x 38.1cm) plastic blow-molded carrying case with handle for easy storage, safe storage, and quick organization. Package include: 3x Receiving Tube, 1x Removal Adapter, 1x Installation Adapter, 1x Screw, 1x Install Cup Adapter, 1x Forcing-screw Press, 1x Receiving Cup, 1x Installing Cup.
- ORION MOTOR TECH - We pursue outstanding quality and professional technical support. If you are not satisfied with this product or if you have any question, please feel free to let us know.
SaleBestseller No. 2
OMT Ball Joint Press Kit, Ball Joint Removal Tool with 4x4 Adapters
- EASY OPERATION: Use the ORION MOTOR TECH Ball Joint Press Tool Set with 4WD Adapter to effortlessly remove press-fit parts including ball joints, U-joints, brake anchor pins, and more on most 2-wheel drive (2WD) and 4-wheel drive (4WD) vehicles without removing the control arm.
- UNIVERSAL COMPATIBILITY: Fits most American domestic and imported cars and light pickup trucks with press-fit type ball joints. Includes a 4WD adapter for service on 1967 - current 1/2 and 3/4 ton 4WD vehicles with the Dana 30 or 44 front axle (found on Ford, GM, Dodge, IHC, and Jeep vehicles).
- PROFESSIONAL-GRADE DURABILITY: Constructed from heavy-duty forged steel with black-oxide finished adapters for maximum strength and longevity that resists rust and corrosion to endure years of heavy use.
- ALL-IN-ONE TOOL KIT: 3x Receiving Tubes, 1x Removal Adapter, 1x Installation Adapter, 1x Screw, 1x Install Cup Adapter, 1x Forcing-screw Press, 1x Receiving Cup, 1x Installing Cup.
- PROTECTIVE CARRYING CASE: Each component is contained in a heavy-duty plastic carrying case with a handle for safe storage and quick organization.
Bestseller No. 3
DAYUAN Ball Joint Press & U Joint Removal Tool Kit, Red Case
- This Ball Joint Press & U Joint Removal Tool compatible for most 2WD and 4WD cars and light trucks
- This tool set is made of ultra carbon steel；these components will stand up to heavy use and accidental drops
- The ball joint press kit is an indispensable tool for your garage; Excellent for removal and installation of press-fit parts such as ball joints. Universal joints and truck brake anchor pins
- This versatile ball joint removal tool kit can also remove rusted and corroded parts and easily tighten rusted parts
- Set contains C-frame press, 3 receiver tubes sizes: 2-3/4”x3"", 2-1/4”x 2-1/2” & 1-3/4”x2”, installation and removing adapters.
SaleBestseller No. 4
OMT Ball Joint Press Kit, Ball Joint Removal Tool with 4x4 Adapters
- 1, EASY OPERATION: The ORION MOTOR TECH Ball Joint Press Set with 4x4 Adapters effortlessly removes press-fit parts including ball joints, U-joints, brake anchor pins, and more on most 2-wheel drive (2WD) and 4-wheel drive (4WD) vehicles without removing the control arm.
- 2, UNIVERSAL COMPATIBILITY: Fits most American domestic and imported cars and light pickup trucks with press-fit type ball joints. Includes a 4WD adapter for service on 1967 - current 1/2 and 3/4 ton 4WD vehicles with the Dana 30 or 44 front axle (found on Ford, GM, Dodge, IHC, and Jeep vehicles).
- 3, PROFESSIONAL-GRADE DURABILITY: Constructed from heavy-duty forged steel with black-oxide finished adapters for maximum strength and longevity that resists rust and corrosion to endure years of heavy use.
- 4, ALL-IN-ONE TOOL SET: 3x Receiving Tubes, 1x Removal Adapter, 1x Installation Adapter, 1x Screw, 1x Install Cup Adapter, 1x Forcing-screw Press, 1x Receiving Cup, 1x Installing Cup.
- 5,PROTECTIVE CARRYING CASE: Each component is contained in a heavy-duty plastic carrying case with a handle for safe storage and quick organization. If you are not satisfied with this product or if you have any questions, please feel free to let us know.
SaleBestseller No. 5
OMT 21pc Ball Joint Press Kit, Ball Joint Tools for 2WD and 4WD Vehicles
- ESSENTIAL TOOL FOR BALL JOINT SERVICE - Use the ORION MOTOR TECH 21PCS Ball Joint Press Set Ball Joint Tool / Bushing Removal Tool with multi-size adapter to effortlessly remove press fit parts including ball joints, U-joints, brake anchor pins, and more on most 2-wheel drive (2WD) and 4-wheel drive (4WD) vehicles without removing the control arm from the vehicle
- UNIVERSALLY COMPATIBLE WITH A WIDE RANGE OF VEHICLES - Use the ORION MOTOR TECH Ball Joint Press Set Ball Joint Tool / Bushing Removal Tool with all the receiver tubes and removing/installing adapters needed to effortlessly remove press fit parts including ball joints, U-joints, brake anchor pins, and more on most GM, Chevy, Ford, and Dodge 2 and 4 wheel drive pickups, vans and sport utility vehicles, will service perfect for vehicles having the Dana 28, 30, 35, 44, 60 axle
- PROFESSIONAL GRADE QUALITY AND DURABILITY - Off road weekend warriors, novices, and professional mechanics trust the ORION kit because ORION MOTOR TECH sources the highest quality components from around the world. Constructed from heavy-duty forged solid carbon steel with anti-rust black-oxide finish on adapters for maximum strength and longevity that resists rust and corrosion
- CONVENIENTLY ORGANIZED IN CUSTOM MOLDED CASE - Ball joint press / bushing/ removal tool kit is enclosed inside a heavy-duty ABS plastic blow-molded carrying case with handle for easy storage, safe storage, and quick organization. Package include: 9x Adapters, 1x Center Rod, 1x C-Frame, 1x Install Adapter, 1x Install Cup, 1x Install Cup Adapter, 1x Receiving Cup, 3x Receiving Tube, 1x Removal Adapter, 1x Screw, 1x Sleeve
- ORION MOTOR TECH - We pursue outstanding quality and professional technical support. If you are not satisfied with this product or if you have any question, please feel free to let us know
This product presentation was made with AAWP plugin.