MBUSA DVUSA Theft-Relevant Parts Policy

“This site contains affiliate links for which OEMDTC may be compensated”

MBUSA DVUSA Theft-Relevant Parts Policy

February 21st 2022

Issued by the Dealer Assistance Center

Policy Profile
Short Title Theft-Relevant Parts (TRP) Policy
Policy Number TRP Policy dated February 21, 2022
Purpose of Policy/Summary This policy defines the process required for acquiring parts identified as parts that may be required to steal a vehicle and/or to give a vehicle a new identity.
Scope of Application This policy applies to all MBUSA and DVUSA Authorized Dealers.
Explanation on Scope of Application Dealers are required to provide verified documentation before fulfillment of an order identified as TRP.
Period of Validity of this Version January 30, 2015 – December 31, 2024
Last Revision of this Version February 21, 2022
Approval Turan Coratekin
Topic Compliance
Policy Owner Kevin Harty, DM – Dealer Assistance Center
Contact Person Bradley Strine, Supervisor – Parts Technical
Documentation Published on NetStar and PAC websites
Documents TRP Order Form (MBUSA-137754962792)
Star Bulletin S-B-80.57/62H, (April 9, 2019): Ordering a Programmed DAS4 key when no keys are present.
Service Information SI80.57-P-0008A Programming and ordering a replacement key or additional key, dated Februar 17, 2021
Form OF80.57-P-3000-01A Register vehicle as present for programming/ordering a DAS4 key
Further Applicable Regulations
Changes to Previous Version New hyperlink added to NASTF SDRM system added 2.D
Note added for vehicle requirements for DAS4 fallback procedure 3.A.i
Note added DAS4 keys and VSPs 3.C.i
Annex 5 added, Service Information SI80.57-P-0008A
Annex 6 added, Form OF80.57-P-3000-01A

 

Applies to: MBUSA Dealers Issued by: Dealer  Assistance Center

 


Mercedes-Benz
Mercedes-Benz

 


1. Definitions

A. Theft-Relevant Parts (TRP)

TRPs are parts that may be required to steal a vehicle and/or to give a vehicle a new identity (see list of TRPs below for definition). The components listed below (series production parts and spare parts) retain their TRP status permanently. Only the current DAS designations are listed in the following listing. Regardless of what the list contains, all parts marked with the TRP and Theft-Relevant Information (TRI) identifiers in the documentation systems and Paragon, in compliance with the procedural instructions shall be considered theft-relevant.

  • Electronic vehicle key
  • Electronic steering lock (ELV, ESL, ESCL)
  • Electronic ignition switch (EZS/EIS) and workshop key for personalization
  • Electronic ignition switch with integrated central gateway (EZS/ZGW, EIS/CGW)
  • Electronic selector lever module (EWM/ESM)
  • Vehicle-related plates, identification plate, production plate, visible VIN plate, including base material
  • Transmission control unit (VGS, TCM)
  • Direct shift module (DSM, ISM)
  • Bodies and body sections/parts for placement of the vehicle identification number
  • Engine control unit (MSG, MCM)
  • Power electronics for electric drive with DAS (TUBE)
  • Hybrid and e-drive control unit (EMx, ME2)
  • Belt-driven or integrated starter-alternator (RSG, ISG) for DAS4
  • Locking sets and mechanical keys

 

B. Theft-Relevant Information (TRI)

TRI is information that may be required to steal a vehicle and/or to give a vehicle a new identity (see list of TRI below for definition).  It includes the following:

  • Locking data record
  • Initialization data
  • Personalization data
  • Disable/enable information

 

2. Theft-Relevant Parts Documentation and Record Keeping

It is the dealer’s responsibility to verify the required documentation before accepting any order for, or delivering, a TRP.  This precaution is necessary to safeguard our customers’ valuable properties and minimize your liability exposure. Failure to adhere to these requirements can expose you, your employees and your dealership to criminal or civil liability in cases of theft or fraud. For these reasons, it is absolutely essential that all personnel adhere to the following documentation process.

Theft-Relevant Parts may only be ordered by the vehicle owner, or his/her authorized representative, or authorized Mercedes-Benz or Freightliner dealerships completing a vehicle repair.

TRP orders for any vehicle not physically located within the USA cannot be accepted. Instead, customers must be referred to the Mercedes-Benz or other Daimler-related service organization in the country where the vehicle is located.

For vehicles which were not originally distributed or sold by Mercedes-Benz USA, LLC (“MBUSA”) or Daimler Vans USA, LLC (“DVUSA”), but reside in the USA, additional documentation requirements may apply when placing orders for TRPs (and any other spare parts) for these non-USA vehicles. All TRP transactions must be documented on the TRP form along with the necessary supporting documentation.

 

A. TRP Documentation for the Vehicle Owner

When an order for a TRP is placed by the vehicle owner, the following documents must be presented:

  • Proof of ownership: The original of the vehicle registration, title, or any ownership document which would be accepted by a Dept. of Motor Vehicles to issue a title. (Copy and retain on file).
  • Proof of Identity: The original of the vehicle owner’s government issued driver/operator license or passport. (Write details on TRP form. Do not copy or retain document).

 

B. TRP documentation for the Authorized Representative of the Vehicle Owner

When an order for a TRP is placed by an authorized representative of the vehicle owner, the following documents must be presented:

  • Proof of ownership: The original of the vehicle registration, title or any ownership document, which would be accepted by a state motor vehicle agency to issue a title. (Copy and retain on file).
  • Proof of Representative’s identity: The original of the authorized representative’s government issued driver/operator license with photo or passport. (Write details on TRP form. Do not copy or retain document).
  • Authorization: An original document authorizing the representative to act on behalf of the vehicle owner. (Retain original in vehicle file).
  • Proof of Owner’s identity: Original or photocopy of the vehicle owner’s government issued driver/operator license with photo or passport. (Write details on TRP form. Do not copy or retain document).

 

An authorized representative may be:

  1. A private citizen or family member acting on behalf of the owner
  2. Independent workshop acting on behalf of their customer
  3. An employee acting on behalf of their employer
  4. A government official acting on behalf of their agency or department
  5. An association member acting on behalf of their association

An authorization letter must come from someone authorized by the company, agency or association to act on its behalf, and include a copy of the authorizer’s personal identification.

 

C. TRP Documentation for Dealership Employees

When an order for a TRP is placed by a dealership employee for the purpose of repairing a dealer owned vehicle presented for service, or completing the key set for unsold vehicles (new or used), the following documentation must be presented:

  • A valid Repair Order authorized by the dealer General Manager or Sales Manager, with the TRP clearly noted.
  • A legibly completed TRP form signed by the requesting employee and delivering employee.
  • Personal identification of dealer employees does not need to be presented.

 

D. TRP Documentation for Vehicle Security Professionals (VSPs) participating in the NASTF Secure Data Release Model (SDRM) Registry

When an order for a TRP is placed by a VSP, the following documentation must be presented:

  • TRP Authorization: Email authorization document that is received by the Dealer after the request is submitted through the MBUSA TRP Ordering web page (at www.startekinfo.com). (Retain printout in vehicle file)
  • VSP Authorization: VSP Registry Positive ID Authorization Form D-1. (Transfer owner details from D-1 onto TRP form, retain D-1 printout in vehicle file). Acts as an Authorization letter and Owner identification. A completed sample form is shown in Annex 4.
  • Proof of ownership: Copy of the vehicle registration, title, or any ownership document which would be accepted by a Dept. of Motor Vehicles to issue a title. (Copy and retain copy on file).
  • VSP Proof of identity: Original or photocopy of the VSP’s government-issued driver/operator license with photo or passport. (Write details on TRP form. Do not copy or retain document).
  • VSP TRP Certification Form: This 2-page form (Annex 2) must be fully completed and signed before the TRP can be handed to the VSP. (Retain original in vehicle file)
  • Repair Order: A valid repair order from the VSP’s business, with the customer name & address, VIN and TRP part number(s) clearly noted. (Retain copy in vehicle file)

For more information on the SDRM registry and how to become a Vehicle Security Professional (VSP), please visit www.nastf.org  Vehicle Security Professional.

 

E. TRP Documentation for Independent Service Providers (ISPs) who are not Vehicle Security Professionals (VSPs)

ISPs who are not Vehicle Security professionals are considered Authorized Representatives as stated in Section 2.B.

 

F. TRP Documentation Verification Process

The dealership employee(s) both accepting and/or delivering TRP must verify that the person presenting the documents is in fact the person identified by the documents.  There must be a clear match between the identification documents and ownership documentation and the person ordering/receiving the TRP. Discrepancies must be resolved or the TRP sale refused.

 

G. TRP Form and Archiving

The TRP form is an essential part of the TRP Process, providing a procedural guideline for TRP transactions and must be fully completed as instructed.

The fully completed and signed TRP form together with all required documents (2A, 2B, 2C, 2D plus Repair Order) shall be archived and kept in a secure location for a period of 6 years. Legible archiving by means of electronic scanning is also possible. All files are subject to audit at any time, and must be available for presentation to representatives of MBUSA or other Daimler related entities or law enforcement authorities at any time for the entire retention period.

 

3. Mercedes-Benz/Freightliner Dealer Workshop and Independent Service Provider (ISP) Ordering Processes

Irrespective of which TRP order process is used, vehicle referencing is mandatory for processing TRP and TRI within the workshop and customer process. This ensures a direct match between the vehicle owner/representative and his/her vehicle and between the TRP and TRI requirements and the vehicle identification number (FIN/VIN).

 

A. Mercedes-Benz or Freightliner Workshop Process for Keys

Particular emphasis shall be placed on ensuring the reliability of TRP handling procedures, with special focus given to the electronic vehicle key and the mechanical vehicle key. 

  • Vehicle keys may not be handed over the counter (including mailing), except to VSPs in strict accordance with Section 3.C. below.
  • Vehicle keys shall in all cases be taken into operation on the vehicle and tested for proper functioning. Testing shall comprise both the mechanical and electronic (as applicable) functions: Opening and locking, release of the immobilizer when the engine is started.
  • The customer shall deliver the vehicle to the dealership for key testing. At the dealer’s option, a dealership employee may dispatched to the vehicle to perform the testing.
  • All documentation requirements remain in effect regardless of where the testing is performed.
  • A Vehicle Security Professional (VSP) may purchase keys as outlined in Section 3.C.i. without the vehicle being presented to the dealer for testing. Testing (verification of key function) must still be performed.

 

i) Process for Ordering Keys when No Keys are Available (DAS4 only)

Dealer must follow the instructions given in Star Bulletin S-B-80.57/62H (or later). This involves completing a form from the Workshop Information System (WIS), creating a XENTRY Diagnosis XSF case, and awaiting the response that Daimler has registered the vehicle. The programmed key must be ordered immediately. Abuse of this process – registering a vehicle via XSF when in fact functioning vehicle keys do exist – may result in penalties for the technician or dealer.

Note Vehicle VIN referencing is critical in cases in where the fall back procedure is used further information can be found in the following Service Information SI80.57-P-0008A “Programming and ordering a replacement key or additional key”, and Form OF80.57-P-3000-01A “Register vehicle as present for programming/ordering a DAS4 key”. (These documents are available in the Work Shop Information System (WIS)).

Note that for lost keys, the tracks for the lost keys must be blocked in order to comply with the TRP policy.  A corresponding note must be made on the Repair Order if the customer declines the recommended repair procedure for keys.

Important Note: It is prohibited for to sell un-programmed vehicle keys or mechanical key blanks.  These parts are solely for use in the Mercedes-Benz / Freightliner Dealer workshop and cannot be sold over the counter.

 

B. Mercedes-Benz or Freightliner Workshop Process for TRP other than Keys

Theft-relevant parts as a matter of policy should only be installed at authorized Mercedes-Benz or Freightliner workshops, certain exceptions apply.  The replacement of TRP components shall be recorded on a repair order as documented proof that the parts were turned over to the customer (entitled customer or authorized representative) at an authorized Mercedes-Benz or Freightliner workshop and that they were installed in the vehicle. Taking components into service that were purchased elsewhere and brought in by the customer to complete the repair is prohibited. The separate legitimization can be omitted if there is an existing workshop order for these components.

The components that apply to the requirements in this section are:

  • Electronic steering lock (ELV, ESL, ESCL)
  • Electronic ignition switch (EZS/EIS) and workshop key for personalization
  • Electronic ignition switch with integrated central gateway (EZS/ZGW, EIS/CGW)
  • Electronic selector lever module (EWM/ESM)
  • Vehicle-related plates, identification plate, production plate, visible VIN plate, including base material
  • Transmission control unit (VGS, TCM)
  • Direct shift module (DSM, ISM)
  • Engine control unit (MSG, MCM)
  • Power electronics for electric drive with DAS (TUBE)
  • Hybrid and e-drive control unit (EMx, ME2)
  • Belt-driven or integrated starter-alternator (RSG, ISG) for DAS4
  • Locking sets and mechanical keys
  • If an updated threat analysis warrants the addition of further TRP, these shall be protected as well

Completion and archiving of the TRP form for repair types listed above can be fully waived under the following five conditions (does not apply to keys, locking sets, key track disabling/enabling):

  1. A valid repair order (noting VIN and customer name and address) is completed and the repair will be carried out in the authorized workshop.
  2. The DAS components are properly listed and identified by part number on the customer/repair order.
  3. The customer/repair order shall be archived for at least 6 years in line with the TRP form retention requirement.
  4. The traceability to the chassis number is ensured.

Example: For a TRP audit pertaining to a certain chassis number, please provide the repair order on which the installation of a DAS component was traceably documented.

  1. The traceability to the part number is ensured.

Example: For a TRP audit pertaining to a certain DAS component with a particular part number, please provide all the repair orders/chassis numbers on which the component was installed within a particular time period.

If compliance with ANY of the items 1 to 5 above cannot be ensured, the TRP form shall be completed and archived in accordance with applicable instructions.

 

C. Independent  Service Provider (ISP) Process for all TRP

Only registered VSPs may purchase the parts listed in this section. ISPs and other authorized representatives who are not VSPs may not purchase parts that are listed in this section.

This ordering process provides a secure ordering channel for those ISPs that are enrolled in the NASTF Vehicle Security Professional (VSP) Registry. Authorized Mercedes-Benz and Freightliner dealers are able to sell the below-listed TRPs to ISPs under the following conditions:

  • ISP must be a member in good standing of the NASTF VSP registry
  • Validated order request is transmitted to the Parts Manager’s inbox which is located on the home page of NetStar
  • The dealer and the ISP should work out the terms and conditions prior to the dealer placing the order in the parts ordering system (Paragon)
  • The ISP must provide the dealer with all necessary documentation (see Section 2D and below) before taking possession of the TRP part
  • Dealer personnel must make sure that there is a clear match with the VSP that ordered the part and the person that is signing for it at the dealer

Following are the part descriptions for parts that can be sold only to VSPs, and not to non-VSP ISPs. Actual part numbers will vary based on the vehicle’s application. An example of each part is provided for identification purposes only. 

  • Electronic steering lock (ELV, ESL, ESCL) g., A208 462 04 30 / A 037 545 16 32
  • Electronic ignition switch (EZS/EIS) and workshop key for personalization g., A 211 545 31 08, including EIS with integrated central gateway (EZS/ZGW, EIS/CGW) e.g., A 164 545 16 00
  • Electronic selector lever module (EWM/ESM) e.g., A 220 267 33 24
  • Transmission control unit (VGS, TCM) e.g., A 000 270 17 00 & A 220 270 31 06
  • Direct shift module (DSM, ISM) e.g., A 000 270 33 52
  • Engine control unit (MSG, MCM) e.g., A 278 900 13 00
  • Keys (see Section 3.C.i below)

Other TRPs not listed in this section may be sold over the counter to non-VSPs. The documentation process in Section 2B of this policy must be followed.

 

i) VSP Process for Keys

Vehicle Security Professionals (VSPs) participating in the NASTF Secure Data Release Model (SDRM) Registry may purchase pre-programmed and/or pre-cut Keys, subject to additional documentation requirements:

  • All documentation outlined in Section 2D must be presented
  • An additional certification (Annex 2) must be completed and presented to the dealer. Dealer must retain the original and keep it with the other TRP documentation for the transaction.
  • Keys may be shipped securely to a VSP.
  • Blank or unprogrammed keys may not be sold under any circumstances.
  • DAS 4 keys require the need for the VSP to maintain an active XENTRY Diagnosis subscription in order to mark the vehicle as present, in cases where an additional key needs to be ordered.
  • For DAS 4 keys, when no keys are present, the VSP must perform vehicle and VIN referencing at the vehicle, along with the submission of all documentation required in section 2.D, to the authorized Mercedes-Benz dealer before the submission of form OF80.57-P-3000-01A via XSF ticket. Failure to complete these steps prior to ordering is in violation of the TRP policy; warnings and fines will be issued in cases where correct DAS 4 procedures are not followed.

Note, additional information and process documentation for DAS 4 key ordering for Vehicle Security Professionals can be found on the PAC Website via NetStar.

 

4. Handling Vehicle Keys

A fundamental rule is that when any vehicle is received, the keys that are handed in for customer vehicles, new vehicles, demonstration vehicles, used vehicles, hired vehicles and the company’s own vehicles must be tested to ensure that they function in the respective vehicle. Non- functioning keys must be determined in the presence of the person handing them in and recorded in writing, with the signature of both the person handing in the key and the person accepting the key.

If a key is lost by the customer, or while the vehicle is in the care of an authorized dealership, the key track(s) in question must be disabled immediately and rendered inoperative by procuring and programming a replacement for the missing key.  The complete mechanical lock set must be replaced to ensure vehicle security. The customer must be informed of the repair. A corresponding note must be made on the repair order if the customer declines the recommended repair procedure for keys.

 

5. Storage of Undelivered TRPs, Handling of Faulty or Unneeded TRPs

Keys and other TRPs received by the dealer and awaiting installation or delivery must be stored in a secure location with limited and controlled access. Dealers must maintain control of the on-hand inventory of all uninstalled TRP at all times.

When a TRP is to be replaced, the old parts which have been removed are not to be handed over to the customer or the customer’s representative. The customer is to be informed of this prior to acceptance of the order. If the customer insists on being given the old part (customer-pay only), receipt of the part must be acknowledged by the customer in writing on the repair order or VSP TRP Certification form as appropriate.

For  quality  analysis,  the  Quality  Evaluation  Center  (QEC)  can  request  TRPs  replaced  under warranty for evaluation. TRPs requested to be returned to MBUSA or DVUSA must be sent using a traceable method.

All  special order TRPs that are not collected by the Customer and all old TRP parts removed for repair purposes, for which return is not planned, must be destroyed and rendered completely inoperable and/or unusable by the dealer, this destruction must be recorded on the TRP form.

 

6. Important Notes

Keys ordered by a dealer cannot be drop-shipped to a third party location (except as outlines in 3.C.i.). Shipments between Authorized Mercedes-Benz / Freightliner Dealers are permitted but discouraged.

Any part that is uniquely coded to the vehicle is not returnable for credit; therefore, the dealer should make every effort to deliver the ordered part to the customer.

If you encounter operational problems with a key or lock from the Fort Worth Key & Lock Site, please complete a Quality Control Sheet and return it with the respective key or lock.   The Key & Lock Site will acknowledge the report and advise the corrective action to be taken.

It is prohibited for to resell un-programmed vehicle keys or mechanical key blanks.  These parts are solely for use in the Mercedes-Benz / Freightliner Dealer workshop and cannot be sold over the counter.

 

7. Policy Audits

MBUSA or DVUSA will randomly select dealers and TRP orders for TRP process review. Selected dealers will receive a written listing of TRP purchases transacted by the dealer and will have a specified time period to respond in writing and provide the necessary TRP documentation. MBUSA or DVUSA will review the TRP documentation and advise the dealer of the issues and concerns identified.

The following corrective actions may be applied for non-conformance of the policy:

  • First Offense – The dealer will be advised of the non-compliance and re-audited within several months to verify effective corrective actions have been taken. It is expected that the dealer will implement robust processes to ensure compliance.
  • Second Offense (1st re-audit) – The dealer may be assessed a $500 administrative fee by MBUSA or DVUSA for each instance (VIN or Part Number) where the TRP process was not followed. A second re-audit will be scheduled.
  • Third Offense (2nd re-audit) – The dealer will be assessed a $1,000 administrative fee by MBUSA or DVUSA for each instance (VIN or Part Number) where the TRP process was not followed.

Further or continuing non-compliance may incur increasing penalties and limitations, including but not limited to a mandatory review of all TRP orders placed by a dealer.

 

Annex 1 – TRP Order Form (MBUSA-137754962792)

This is a sample of the TRP Form Sheet.  Always download the latest version of this form before using it.  This form can be found on the PAC website and at www.startekinfo.com

 

Annex 2 – VSP Key Certification Form

This is a sample of a two-page form available from the PAC Website and www.startekinfo.com. Download the latest version of this form before using it. This form must be completed and retained by the dealer when selling any TRP to a VSP. Only original, hand-written signatures are allowed.

             

Annex 3 – DAS4 Fallback process

Star Bulletin S-B-80.57/62H, dated April 9, 2019 – Ordering a Programmed Key when no keys are present – “The Fallback process”. (First page only). Refer to complete document for important details.

 

Annex 4 – Sample completed NASTF D-1 form

The North American Service Task Force (NASTF) required all Vehicle Security professionals (VSPs) to complete a D-1 form within 2 days of any TRP request. Here is a sample completed ‘online’ form. (A handwritten version is also valid). Any missing information (e.g., owner ID number) must be taken from the document (e.g., copy of owner’s driver license) in accordance with the requirements of section 2.D:

 

Annex 5 – Service Information: Programming and Ordering a replacement key or additional key, SI80.57-P-0008A

 

Service information covering the workshop and parts department process for programming and ordering a replacement key or additional key. Refer to complete document for important details, found in the Work Shop Information System (WIS).

 

Annex 6 – Register vehicle as present for programming/ordering a DAS4 key, OF80.57-P-3000-01A

Organizational Form required with XSF Ticket when conducting the DAS4 fallback procedure. Refer to complete document for important details, found in the Work Shop Information System (WIS).

 


https://www.startekinfo.com/service/download-document/outside/224078/

February 21st 2022

https://static.oemdtc.com/TSB/224078.04.15.2022.pdf

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [880.10 KB]

 


April 15 2020

https://static.oemdtc.com/TSB/MBUSA TRP Policy.pdf

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [816.59 KB]

 


 

Bestseller No. 1
Tukellen for Mercedes Benz Key fob Cover,Special Soft TPU Key Case Protector Compatible with Mercedes Benz 2017-2021 E-Class 2018-2021 S-Class 2019-2021 A-Class C-Class G-Class-White
  • Fits Model:2017-2021 E-Class 2018-2021 S-Class 2019-2021 A-Class C-Class G-Class keyless entry remote control smart key(only keyless go), it will not cover the original car logo on your car key.
  • Attention Please:Because even if the type of the car is the same, the car key might be different based on the different year of manufacturing, so please Double Check your Key Fob with the picture at left before Purchasing.
  • Material: Made with premium TPU. Super thin, soft, trending looking and pretty durable. Make your key fob look new and premium.
  • 360 Degree protection: Full protection of back and forth, left and right. It can effectively protect your car key from falling, shock, scratch and dust.
  • After-sales:Unconditionally refund or free replace if any defective or quality problems, any problem please feel free to contact us, we offer life-time friendly customer service.
Bestseller No. 2
PIFOOG for Mercedes Key Fob Cover TPU Key Case Soft Car Keys Protector Fit Mercedes Benz AMG C E M S CLS CLA GLK GLA GLC GLE Smart Remote Key Keychain Girly Women White Gold
  • Specific for Mercedes : Perfect fit for Benz 3 Button Keyless Entry smart keys like Mercedes Benz AMG GT, C E S M R CLA CLS GLA GLC GLE GLK GLS SLC SLK SL GL CL Class etc. (Kindly Note :(NOTE :Three kinds of keychains are be sent randomly. (see picture 2) )
  • Easy to Press : PIFOOG's soft TPU key fob cover for Mercedes Benz is made of high-quality TPU material. Soft and excellent touch feeling makes easier to press the buttons.
  • Do Not Fade : Adopted excellent plating technology for Mercedes key fob cover, not fading and anti-scratches. Come with an anti-lost keychain for Mercedes Benz smart keys, better protect your car keys for Mercedes from scratches and losing.
  • Full Signal : Original car key design. The light and thin TPU material ensures worry-free signal transmission and does not affect the Mercedes-Benz key fob signal induction.
  • 30-Day Free Return & 365-Day Warranty : PIFOOG offers free returns within 30 days and ONCE replacement within 365 days for the accessories for Mercedes Benz. Any question, just contact PIFOOG.
Bestseller No. 3
ELOHEI for Mercedes Benz Key Fob Cover, Premium Soft TPU Key Case Cover Compatible with Mercedes Benz C E S M CLS CLK G Class Keyless Smart Key Fob (Gold Edge Black)
  • Fits models: This Key Fob Cover is fit for Mercedes Benz C E M S CLS CLK GLK GLC G Class etc.it will not cover the original car logo on your car key.
  • Note: Even though the car model is the same, but the car key might be different based on the different year of manufacturing,Please check carefully whether your keys match our pictures before buying.
  • Comprehensive protection: All-inclusive design, anti-drop and anti-scratch, effectively protects the car key.a variety of colors to enrich your color needs.
  • Material: High quality TPU material for good signal reception. No signal blocking.The TPU silicone protective cover is a cover that adapts to your ignition key using flexible silicone. The car key silicone case is tearproof and non-slip.
  • After-sales: full refund and replacement for the lifetime. If you have any issue, Please feel free to contact us through seller support.
Bestseller No. 4
Vitodeco Leather Keyless Entry Remote Control Smart Key Case Cover with a Key Chain Compatible for Mercedes Benz (Black)
  • Suitable for Mercedes Benz 4 buttons or 3 buttons keyless entry remote control smart key. Please compare picture with your key before purchase.
  • This case made from 100% genuine premium cowhide leather. Provide full protection from scratch and wear-out for your key.
  • All buttons, ports, sensors remain unrestricted without compromising on protection. This case is designed for everyday use.
  • Easy to install, instantly improve the appearance of your old or dirty remote control smart key.
  • Package Included: 1 X Leather Key Case, and 1 X Key Chain (Key Fob not included)
Bestseller No. 5
PIFOOG Key Fob Cover for Mercedes TPU White Gold Bling Keychain Accessories Fit Benz GLA GLE GLB GLS GLC CLA CLS C300 AMG A E S G Class Cute Car Keys Case Shell Girly Women
  • Specific for Benz : PIFOOG's 4-button key cover perfect fits for Mercedes - Benz A-Class 2019 - 2022, AMG GT 2019 - 2022, C-Class 2019 - 2021, C-Class C300 Cabriolet (2022), CLA 2020 - 2022, CLS 2019 - 2022, E-Class 2017 - 2022, G-Class 2019 - 2021, GLA 2021 - 2022, GLB 2020 - 2022, GLC 2020 - 2022, GLE 2020 - 2022, GLS 2020 - 2022, S-Class 2018 - 2020, S-Class AMG S63 (2021). (Note :Two kinds of keychains are be sent randomly. (Pls see picture 2.)
  • Easy to Press : PIFOOG's gold key fob cover for Mercedes Benz is made of high-quality TPU material. Soft and excellent touch feeling makes easier to press the buttons.
  • Full Signal : Original car key design. The light and thin TPU material ensures worry-free signal transmission and does not affect the signal for Mercedes smart keys.
  • Do Not Fade : Adopted excellent plating technology for key case for Mercedes Benz, not fading and anti-scratches. Come with an anti-lost and cute car keychain for Benz, better protect your 4 buttons key fob for Mercedes from scratches and losing.
  • Idea Gifts : Package includes 1PC TPU gold car key accessory for Mercedes Benz, 1PC anti-lost D-buckle, 1PC bling round spring clip which helps hook it on your bag, and 2PCS small rings keeping your home keys. It's a best gift for family, friends and colleagues on Mother's Day, Father's Day, birthday, Christmas etc.
Bestseller No. 6
Compatible with Mercedes Benz Key Fob Cover, Premium Soft TPU Full Protection Key Case for Mercedes Benz A B C E S G M Class CLK CLS GLA 3-Buttons Smart Key Shells (Silver)
  • 【Fits Model】 For Mercedes-Benz A B C E G S R CLS CLK Class CLA GLA GLC GLE GLK GLS SLK SLS W164 W204 W205 S204 S205 W212 W221 CL203 A207 C207 etc. 3 buttons smart key fob cover.
  • 【Attention】: Even if the type of the car is the same, the car key fob might be different based on the different year of manufacturing, so please DOUBLE CHECK your key fob with the picture at left before you place the order, the same shape can be applied, thanks!
  • 【360 Degree Protection】 Full coverage, the key cover protect your key fob like a glove, effectively protect the key from failing, scratch and dust. Make your key fob always keep new and also won't affect the key signal.
  • 【High Quality Material】 The key fob case is made of high-quality TPU material. It is ultra-thin, soft and fashionable. Easier to press the button, and only need 1-2 mintues to complete installation or remove it.
  • 【Stylish Design】 High-quality leather texture design, stylish and elegant shows your taste and also makes a great gift for family, friends and colleagues.
SaleBestseller No. 7
PIFOOG for Mercedes Key Fob Cover 3 Buttons Soft TPU Keys Protector Bling Keychain for Mercedes Benz C E M S CLS CLA GLK GLA GLC GLE AMG Class Girly Cute White Silver
  • Specific for Mercedes : PIOOG's 3-button key fob cover fit for Mercedes AMG GT, C E S M R CLA CLS GLA GLC GLE GLK GLS SLC SLK SL GL CL Class smart keys. (Kindly Note : Please confirm your car keys shape same as pictured before purchasing.)
  • Easy to Press : PIFOOG's TPU key cover for Mercedes Benz is made of high-quality TPU material. Soft and excellent touch feeling makes easier to press the buttons.
  • Do Not Fade : Adopted excellent plating technology for Mercedes - Benz key fob case, not fading and anti-scratches. Come with an anti-lost and bling bling keychain for Mercedes Benz smart keys, better protect your key fob for Mercedes from scratches and losing.
  • Full Signal : Original car key design. The light and thin TPU material ensures worry-free signal transmission and does not affect the remote key fob for Mercedes signal induction.
  • 30-Day Free Return & 365-Day Warranty : PIFOOG offers free returns within 30 days and ONCE replacement within 365 days for the tpu car key accessories for Mercedes Benz. Any question, just contact PIFOOG.
Bestseller No. 8
Autophone Compatible with Mercedes Benz Key Fob Cover with Keychain,Soft TPU 360 Degree Protection Key Case for 2019-2021 A-Class C-Class G-Class 2017-2020 E-Class S-Class (White)
  • 【Attention Please】Because even if the type of the car is the same, the car key might be different based on the different year of manufacturing, so please Double Check your Key Fob with the picture at left before Purchasing.
  • 【Compatible With】2017-2021 E-Class, G-Class,2018-2019 S-Class W213,etc. Keyless entry remote control smart key(only keyless go)
  • 【Material】Made with premium TPU. Super thin, soft, trending looking and pretty durable. Make your key fob look new and premium.Metal plus textile key chain keeps your keys from being lost, making it easy to carry around, suitable for both men and women.
  • 【Full Protection】This keychain is full cover 360 degrees protection. Fits your key fob like a glove,prevent your key from shock and scratch.
  • 【Worry free after sale】Unconditionally refund or free replace if any defective or quality problems, any problem please feel free to contact us, we offer life-time friendly customer service.
Bestseller No. 9
ELOHEI for Mercedes Benz Key Fob Cover, Premium Soft TPU 360 Degree Full Protection Key Case Accessories for Mercedes Benz E Class, 2018-up S Class, 2017-2022 C-Class G-Class A-Class
  • Fits models: This Key Fob Cover is fit for Mercedes Benz Keyless Smart Key Fob E Class (E300 E400 E43, etc. ), 2018 up S Class, 2017 2018 W218, it will not cover the original car logo on your car key.
  • Note: Even though the car model is the same, but the car key might be different based on the different year of manufacturing,Please check carefully whether your keys match our pictures before buying.
  • Comprehensive protection: All-inclusive design, anti-drop and anti-scratch, effectively protects the car key.a variety of colors to enrich your color needs.
  • Material: High quality TPU material for good signal reception. No signal blocking.The TPU silicone protective cover is a cover that adapts to your key using flexible silicone. The car key silicone case is tearproof and non-slip.
  • After-sales: full refund and replacement for the lifetime. If you have any issue, Please feel free to contact us through seller support.
Bestseller No. 10
PIFOOG for Mercedes Key Fob Cover 3 Button Pink TPU Bling Car Key Chain Accessories Keys Case Shell Protector for Mercerdes Benz AMG GLC GLA CLA GLS GLE GLK CLS C 300 G E S ML Class Women Girly
  • Specific for Mercedes - Benz: PIFOOG TPU pink key cover perfectly fits for Benz AMG GT 2016 - 2018, AMG GT R 2019 - 2020, C Class 2009 - 2018, E Class 2009 - 2016, G Class 2010 - 2018, CLA 2014 - 2019, CLS 2012 - 2018, GLA 2015 - 2020, GLC / GLE 2016 - 2019, GLK 2011 - 2015, GLS 2017 - 2019, S - Class 2010 - 2017, SLC 2017 - 2020, R Class, SLK, ML, SL, GL, CL (Note: The car model is for reference only. Pls confirm your car keys shape and buttons patterns same as pictured before buying.)
  • Not Easy to Fade: Adopting a three-layer electroplating process for the 3 buttons key fob cover for Mercedes Benz, it remains unfaded and resistant to scratches. The button patterns stay clear and easily readable even after prolonged use.
  • Unique Anti-Lost Keychain: The D-shaped ring with a cross lock is more secure and locks tighter compared to the traditional spiral type, preventing keys from falling off or getting lost. PIFOOG's pink car key case for Mercedes Benz adopts a fully enclosed design, which effectively prevents your key from being scratched, damaged, or wet.
  • Full Signal: The lightweight and thin TPU material ensures worry-free signal transmission and does not interfere with your 3 - button smart key for Mercedes - Benz. The signal strength is 3-4 times stronger than that of metal key shell.
  • 30-Day Free Return & 365-Day Warranty : PIFOOG offers free returns within 30 days and ONCE replacement within 365 days for the pink car key accessories for Mercedes Benz. Any question, just contact PIFOOG.

Last update on 2024-03-09 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

 


Leave a Comment

Share to...