December 21, 2020 NHTSA CAMPAIGN NUMBER: 20V802000
Air in the brake system can result in extended brake pedal travel, increasing the risk of a crash.
NHTSA Campaign Number: 20V802
Manufacturer Daimler Vans USA, LLC
Components SERVICE BRAKES, HYDRAULIC
Potential Number of Units Affected 9,094
Summary
Daimler Vans USA, LLC (DVUSA) is recalling certain 2019-2020 Mercedes-Benz
Sprinter and Freightliner Sprinter vehicles equipped with electric parking brakes. The rear brake calipers may leak brake fluid into the housing of the electric parking brake connected to the rear axle service brake system, allowing air to enter the hydraulic brake system.
Remedy
DVUSA has not yet established a remedy. DVUSA issued owners an interim notification on January 21, 2021. The remedy is expected to be available in December 2021. Owners may contact DVUSA customer service at 1-877-762-8267. DVUSA’s number for this recall is VS3BREPB.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Check for Daimler Vans Recalls
| TO: Mercedes-Benz Principals, Freightliner Principals, General Managers, Sales Managers, Service Managers, Parts Managers | FROM: Anthony Washington, Department Manager, Regulations and Certifications |
| Re: Initial Recall Campaign Notification Model 907 (Sprinter) Model Years 2019-2020 Rear Axle Brake Caliper | DATE: December 21, 2020 |
IMPORTANT RECALL CAMPAIGN INFORMATION
Please see the attached documents related to the campaign listed above
| Campaign No. : | Campaign Desc. : | Rear Axle Brake Caliper | |
| 2020120019 | PDGBREPB | ||
| This is to notify you of an upcoming Recall Campaign concerning the rear axle brake calipers on approximately 9,094 MY19-20 Mercedes-Benz & Freightliner Sprinter vans. The recall campaign will be visible on the www.safercar.gov website and may generate questions from customers. All affected VINs will be flagged as “Pending” in VMI. | |||
| Background | |||
| Issue | Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz and Freightliner vans, has determined that on certain Sprinter vehicles from platform 907 (VS30) equipped with an electrical parking brake (EPB), if the EPB is used frequently, then over time, the brake caliper of the rear axle may leak brake fluid into the housing of the electric parking brake that is connected to the rear axle service brake system. This could allow air to enter the hydraulic brake system which could lead to extended brake pedal travel and a changed brake pedal feel. If the condition is not addressed, the risk of a crash could increase. | ||
| What We’re Doing | MBUSA/DVUSA is conducting a voluntary recall. MBAG is currently working on developing a final technical remedy. For this purpose, various development and production optimization measures are currently being implemented with the supplier. | ||
| Parts | Parts are still being verified.
An additional notification will be sent when parts are available for repair. | ||
| Vehicles Affected | |||
| Vehicle Model Year(s) | Model Year 2019-2020 | ||
| Vehicle Model | Sprinter, VS30, Platform 907 | ||
| Vehicle Populations | |||
| Total Recall | 9,094 | ||
| Dealer Inventory | 740 | ||
| Given this notice, it is a violation of Federal Law for a dealer to sell or lease any new Sprinter vehicles in dealer inventory covered by this notification until the vehicle has been repaired.
Loaner and demonstrator vehicles may continue to be driven, but must not be retailed until repaired.
Additionally, given this notice, it is a violation of Federal Law for rental companies to rent new Sprinter vehicles covered by this notification until the vehicle has been repaired.
| |||
| Next Steps/Notes | |||
| Customer Notification Timeline | An owner notification letter will be mailed in early February 2021. | ||
| AOMS/SOMS | AOMs – This recall may generate questions from your dealers. Please forward this notice to your dealers ASAP. | ||
| Rental Fleet Partners | This recall may affect vehicles in your fleet. Please contact your respective MBUSA/DVUSA fleet representative for further information and next steps. For repairs, please contact your preferred MBUSA/DVUSA dealer. | ||
| While we regret any inconvenience this may cause, we are determined to maintain a high level of vehicle quality and customer satisfaction. | |||
| TO: Mercedes-Benz Principals, General Managers, Sales Managers, Service Managers, Parts Managers | FROM: Anthony Washington, Department Manager, Regulations and Certifications |
| Re: Recall Campaign Launch Notification Model 907 (Sprinter) Model Years 2019-2020 Replace Rear Axle Brake Calipers | DATE: December, 2021 |
IMPORTANT RECALL CAMPAIGN INFORMATION
Please see the attached documents related to the campaign listed above
| Campaign No. : | Campaign Desc. : | Replace Rear Axle Brake Calipers | |
| 2021030006 | VS3BREPB | ||
| This is to notify you of the Recall Campaign launch to replace the rear axle brake calipers on approximately 7,179 MY19-20 Mercedes-Benz Sprinter vans. The recall campaign will be visible on the www.safercar.gov website and may generate questions from customers. All affected VINs will be flagged as “OPEN” in VMI | |||
| Background | |||
| Issue | Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz Sprinter Vans, has determined that on certain Sprinter vehicles from platform 907 (VS30) equipped with an electric parking brake (EPB), if the EPB is used frequently, then over time, the rear axle brake caliper may leak brake fluid into the EPB housing that is connected to the rear axle service brake system. This could allow air to enter the hydraulic brake system which could lead to extended brake pedal travel and a different brake pedal feel.
If the condition is not addressed, the risk of a crash could increase. | ||
| What We’re Doing | MBUSA is conducting a voluntary recall. An Authorized Mercedes-Benz dealer will replace the rear brake caliper. | ||
| Parts | Parts are available. | ||
| Vehicles Affected | |||
| Vehicle Model Year(s) | Model Year 2019-2020 | ||
| Vehicle Model | Sprinter, VS30, Platform 907 | ||
| Vehicle Populations | |||
| Total Recall | 7,179 | ||
| Dealer Inventory | 1 | ||
| Given this notice, it is a violation of Federal Law for a dealer to sell or lease any new Sprinter vehicles in dealer inventory covered by this notification until the vehicle has been repaired.
Loaner and demonstrator vehicles may continue to be driven, but must not be retailed until repaired.
Additionally, given this notice, it is a violation of Federal Law for rental companies to rent new Sprinter vehicles covered by this notification until the vehicle has been repaired.
| |||
| Next Steps/Notes | |||
| Customer Notification Timeline | An owner notification will be mailed January, 2022 | ||
| AOMS/SOMS | AOMs – This recall may generate questions from your dealers. Please forward this notice to your dealers ASAP. | ||
| Rental Fleet Partners | This recall may affect vehicles in your fleet. Please contact your respective MBUSA fleet representative for further information and next steps. For repairs, please contact your preferred Mercedes-Benz dealer. | ||
| While we regret any inconvenience this may cause, we are determined to maintain a high level of vehicle quality and customer satisfaction. | |||
Campaign No. 2021030006, April 2021
| TO: | ALL MERCEDES-BENZ CENTERS |
| SUBJECT: | Model 907 Sprinter, Model Year 2019-2020 Electric Parking Brake Rear Brake Calipers |
Mercedes-Benz AG (“MBAG”), the manufacturer of Mercedes-Benz vans, has determined that on certain Sprinter vehicles from platform 907 (VS30) equipped with an electrical parking brake(EPB), if the EPB is used frequently, then over time, the brake caliper of the rear axle may leak brake fluid into the housing of the electric parking brake that is connected to the rear axle service brake system. This could allow air to enter the hydraulic brake system which could lead to extended brake pedal travel and a changed brake pedal feel. If the condition is not addressed, the risk of a crash could increase. MBUSA is conducting a voluntary recall. An authorized Mercedes Benz dealer will replace the rear brake calipers.
Prior to performing this Recall Campaign:
• Please check VMI to determine if the vehicle is involved in the Campaign and if it has been previously repaired.
• Please review the entire Recall Campaign bulletin and follow the repair procedure exactly as described.
Please note that Recall Campaigns do not expire and may also be performed on a vehicle with a vehicle status indicator.
Approximately 7,179 vehicles are involved.
Order No. V-RC-2021030006
SEOCONTENT-START
IMPORTANT SAFETY RECALL INTERIM NOTICE
This notice applies to your vehicle, VIN: 123456
Rear Brake Caliper
NHTSA Recall #20V802
January, 2021
20V802
123456
Dear Valued Mercedes-Benz Sprinter Owner:
This notice is sent to you in accordance with the requirements of the National Traffic and Motor Vehicle Safety Act.
Mercedes-Benz AG (“MBAG”), the manufacturer of Sprinter vans, has decided that a defect which relates to motor vehicle safety
exists in certain Model Year 2019 – 2020 Mercedes-Benz Sprinter vehicles. Our records indicate that your vehicle is included in
the affected population of vehicles.
MBAG has determined that the brake caliper of the rear axle may leak brake fluid into the housing of the electric parking brake
connected to the rear axle service brake system, which could lead to extended brake pedal travel and a changed brake pedal
feel. If the condition is not addressed, there might be an increased risk of a crash.
MBAG is currently working on developing a final technical remedy and therefore, the parts to remedy this issue are
currently not yet available.
We are working to obtain the necessary parts to correct this condition as quickly as possible. As the parts become available, we will
send you another letter asking you to take your vehicle to an authorized Mercedes-Benz dealer to have the recall completed free of
charge.
Should you have any concerns or questions regarding your vehicle before you receive the next recall letter when parts are
available, please contact an authorized Mercedes-Benz dealer. If for any reason a dealer is unable to remedy your situation, we
are always happy to hear from you. Please contact us at 1-800-367-6372. A new vehicle identification number (VIN)-based recall
lookup tool on our MBUSA.com website, offers a search function that will indicate whether a vehicle has been subject to a safety
recall, and whether that vehicle has had the free remedy performed.
Please visit www.mbvans.com/sprinter/owners-resources/recall and enter your 17 digit VIN in the VIN Look-up tool.
We also encourage you to sign up for recall alerts at www.nhtsa.gov/alerts.
In the event that you are no longer the vehicle owner, or have had a change of address, please complete the reverse side and return
the updated information in the enclosed envelope. If this is a leased vehicle and the lessor and registered owner receive this notice,
please forward this information by first class mail to the lessee within 10 business days to comply with Federal Regulations.
We apologize for any inconvenience this situation may cause you.
Sincerely,
• A safety defect exists in your vehicle.
• Remedy parts are not yet available for your
vehicle.
• We will contact you again once parts are
available.
Mercedes-Benz USA, LLC
Robert Veit
Managing Director
Vans USA
Mercedes-Benz USA, LLC
A Mercedes-Benz AG Company
One Mercedes-Benz Drive
Sandy Springs, GA 30328
Phone (770) 705-0600
IMPORTANT
If for any reason YOU NO LONGER OWN THIS VEHICLE OR have a CHANGE OF ADDRESS, please COMPLETE THE SECTION
BELOW, place in the ENCLOSED ENVELOPE, and DROP IN ANY MAIL BOX. If possible, provide the name and address of the
present owner so that we may contact them.
! EXPORTED
! LEASE, VEHICLE RETURNED
! SCRAPPED
! SOLD
! STOLEN
! OTHER
! NEW OWNER INFORMATION ! MY NEW NAME OR ADDRESS IS:
Last Name, First Name
Street Apt
City State ZIP
Email Address
Phone (numbers only) Mobile (numbers only)
———————————————– ———————————————————————————-
Date Signature
VIN: 123456
****************************************************************************************************************
Model 907, 910
with code B25 (Electric parking brake)
Operation no. of the operation texts or standard texts and flat rates
Category Op. no. Operation text Time Acc. no. Code
L 02 1250 Operations: Replace 2 brake calipers of rear axle 2.3hrs 42 960 93 VS3BREPB
L 02 1586 Operations: Extra work for removing/installing 2
wheel and tire assemblies during installation with
wheel lift dolly
0.2hrs 42 960 93 VS3BREPB
L 02 1285 Operations: Extra work for bleeding hydraulic brake
system (after repair work) on veh. with manual
transmission
0.1hr 42 960 93 VS3BREPB
L 02 1286 Operations: Perform brake test stand run 0.1hr 42 960 93 VS3BREPB
L 02 3282 Operations: Remove underfloor paneling (when
working on veh.)
0.2hrs 42 960 93 VS3BREPB
L 02 3283 Operations: Remove lower engine compartment
lining (when working on vehicle)
0.2hrs 42 960 93 VS3BREPB
D42.10-A004-79
1 Brake caliper 5 Electrical wiring harness 9 Brake hose
2 Bracket 6 Screw 10 Dust cap
3 Screw 7 Electrical connector 11 Screw
4 Electrical wiring harness 8 Actuator motor
V-RC-2021030006 1
Replace both rear-axle brake calipers, along with actuator motors of electric parking brake.
Replacement of wear or damaged parts must be invoiced separately.
aDanger Risk of death caused by vehicle
slipping or toppling off of the lifting
platform.
Align vehicle between vehicle lift
columns and position the four
support plates at the vehicle lift
support points specified by the
vehicle manufacturer.
AS00.00-Z-0010-01A
aDanger Risk of accident when
commissioning the vehicle due to
a lack of braking effect when the
service brake is operated for the
first time after repair work.
Before starting the engine, actuate
brake pedal several times until
pressure is built up and
maintained in the brake system.
AS42.50-Z-0002-01A
aWarning Risk of injury. Skin or eye injuries
may result when handling hot or
glowing objects.
Wear protective gloves, protective
clothing and safety glasses, if
necessary.
AS00.00-Z-0002-01A
aCaution Risk of poisoning from
swallowing brake fluid. Risk of
injury from skin and eye contact
with brake fluid
Only pour brake fluid into suitable
and appropriately marked
containers. Wear protective
clothing and eye protection when
handling brake fluid.
AS42.50-Z-0001-01A
Topical note Information on preventing damage
to electronic components due to
electrostatic discharge
AH54.00-P-0001-01A
Topical note Notes on repairs to brake system AH42.00-P-0003-01A
Topical note Brake fluid notes AH42.50-P-0001-01A
Topical note Notes on self-locking nuts and
bolts
AH00.00-N-0001-01A
Topical note Notes on bleeding brake system AH42.10-N-0002-01A
Topical note Notes on carrying out repair work
in the vehicle interior
AH68.00-N-0001-01S
g Check
1 Check, whether the vehicle is
affected by the measure.
SM42.10-D-0046-01AAA
SM42.10-D-0046-01AAB
Affected vehicles: Replace brake
calipers on rear axle (code:
VS3BREPB, acc. no.: 42 960 93)
Model 907.### ## as of 000025 up
to 322015
i
For authorized Mercedes‑Benz
service partners, only the entry in
the Extended VEGA Application
(EVA) system, in the “Current” tab,
is decisive. An additional test of the
affected vehicles in the workshop
information system (WIS) or vehicle
list is thereby not necessary.
2 V-RC-2021030006
e Remove
2 Clean area surrounding cap of
brake fluid reservoir.
Assembly cleaner BR00.45-Z-1028-04A
3 Remove cap from brake fluid
reservoir.
4 Check fill level in brake fluid
reservoir.
p
The fill level must not be above the
maximum marking.
This prevents the brake fluid
reservoir from overflowing when
the brake pistons are pushed back.
If the fill level in brake fluid
reservoir is too high,
↓
extract brake fluid.
i
Commercially available devices/
tools
Extraction bellows
5 Move rear axle brake pads into
assembly position.
f AR42.10-D-1710-01TS
p
Do not operate the service brake
while “Move to assembly position”
is shown.
Otherwise, the spindle of the brake
caliper (1) will be damaged.
6 Remove rear wheels.
f AR40.10-D-1100TS
7 Remove electrical wiring harness
from holder (2).
8 Disconnect electrical wiring
harness (4) from electrical wiring
harness (5) to electrical connector.
9 Remove electrical wiring harness
(5) from brake caliper (1).
i
To do this, remove screw (6).
10 Disconnect electrical connector (7)
from actuator motor (8).
11 Remove brake pads on rear axle.
f AR42.10-D-1710TS
i
Reuse brakepads.
12 Remove brake hose (9) on vehicle
side.
f AR42.10-D-0023TS
13 Remove dust cap (10).
V-RC-2021030006 3
14 Remove brake caliper (1). i
To do so, remove screw/bolt (11).
Replace bolt (11).
i
When replacing brake calipers (1),
only install brake calipers (1) from
the same manufacturer and model
on an axle.
g Check
15 Check brake hose (9) for damage. If damage exists,
↓
Replace brake hose (9) subject to
separate invoice.
f AR42.10-D-0023TS
16 Modify brake hose (9).
f AR42.10-D-0023TS
d Install
17 Install new brake caliper (1). i
To do so, screw in new bolt (11).
n Screw/guide pin, brake caliper
to brake caliper support
BA42.10-N-1006-12TS
18 Install dust cap (10).
19 Install brake hose (9) on vehicle
side.
f AR42.10-D-0023TS
i
Do not yet bleed brake system.
20 Install old brakepads of rear axle.
f AR42.10-D-1710TS
i
Do not operate brake pedal yet.
21 Connect electrical connector (7) to
actuator motor (8).
22 Attach electrical wiring harness (5)
to brake caliper (1).
i
Screw in bolt (6) to do this.
n Bolt, wiring harness for wear
indicator to brake caliper
BA42.10-N-1004-12TS
23 Connect electrical wiring harness
(4) with electrical wiring harness
(5) to electrical connector.
24 Install electrical wiring harness on
holder (2).
4 V-RC-2021030006
25 Deactivate brake pad change
mode.
f AR42.10-D-1710-01TS
p
Whilst doing so, do not actuate
service brake.
Otherwise, the spindle of the brake
caliper (1) will be damaged.
26 Bleed brake system.
f AR42.10-D-0010TS
27 Fit brake pads on rear axle. i
For this, depress brake pedal
several times until the brake pads
contact the brake disks.
Firm resistance should be
noticeable at the brake pedal.
28 Mount rear wheels.
f AR40.10-D-1100TS
Update software / Reset counter
29 Connect diagnostic system.
a AD00.00-D-2000-06TS
i
It is absolutely essential to
precisely follow the operation steps
as described in the vehicle
diagnosis system.
30 Connect charging equipment.
f Maintaining on-board electrical
system voltage when performing
test and diagnosis work on vehicle
AR54.10-D-1127TS
p
During the entire work procedure a
sufficiently large voltage supply
must be provided for the vehicle’s
on-board electrical system.
Otherwise any undervoltage that
occurs may damage the control
units.
i
Follow the operating instructions
for the charger.
i
Use the charger to ensure that an
adequate power supply (min.
12.5 V) is provided for the onboard
electrical system battery.
31 Update software for ESP® control
unit.
i
It is absolutely essential to
precisely follow the operation steps
as described in the vehicle
diagnosis system.
V-RC-2021030006 5
32 Reset actuator counter of electric
parking brake.
i
To do this, select the following
menu items:
Control units view →
N30/4 – Electronic Stability
Program (ESP®) →
Adaptations →
Teach-in processes →
Resetting of ‘Electric parking brake’
counter
i
It is absolutely essential to
precisely follow the operation steps
as described in the vehicle
diagnosis system.
33 Disconnect diagnostic system.
a AD00.00-D-2000-06TS
34 Remove charger from vehicle.
f AR54.10-D-1127TS
g Check
35 Perform brake test on test stand.
e AP42.00-D-4290TS
n Rear axle brake caliper
Number Designation Model 907
except code
IT5 (5.0 tonner)
BA42.10-N-1004-12TS Bolt, wiring harness for wear indicator to brake caliper Nm 8
n Rear axle brake caliper
Number Designation Model 907
except code
IT5 (5.0 tonner)
BA42.10-N-1006-12TS Screw/guide pin, brake caliper to brake caliper support Nm 34
Repair materials
Number Designation Order number
BR00.45-Z-1028-04A Assembly cleaner A 000 986 56 01
6 V-RC-2021030006
Parts ordering note
Part no. Designation Quantity
A 000 989 08 07 11 Brake fluid (1L) n. B.
Parts scope, model 907
A 907 423 82 00 Left brake caliper n. B.
A 907 423 83 00 Right brake caliper n. B.
Replace brake calipers on rear axle (code: VS3BREPB, acc. no.: 42 960 93) SM42.10-D-0046SG
V-RC-2021030006 7
****************************************************************************************************************
SEOCONTENT-END
16 Affected Products
Vehicles
| MAKE | MODEL | YEAR |
| FREIGHTLINER | SPRINTER 1500 | 2019-2020 |
| FREIGHTLINER | SPRINTER 2500 | 2019-2020 |
| FREIGHTLINER | SPRINTER 3500 | 2019-2020 |
| FREIGHTLINER | SPRINTER 4500 | 2019-2020 |
| MERCEDES-BENZ | SPRINTER 1500 | 2019-2020 |
| MERCEDES-BENZ | SPRINTER 2500 | 2019-2020 |
| MERCEDES-BENZ | SPRINTER 3500 | 2019-2020 |
| MERCEDES-BENZ | SPRINTER 4500 | 2019-2020 |
13 Associated Documents
Recall 573 Report- Amendment 3
RCLRPT-20V802-6449.PDF 216.08KB
Recall 573 Report- Amendment 4
RCLRPT-20V802-1946.PDF 216.1KB
Defect Notice 573 Report
RCLRPT-20V802-8460.PDF 214.907KB
Recall Acknowledgement
RCAK-20V802-5560.pdf 245.028KB
Recall 573 Report- Amendment 2
RCLRPT-20V802-8569.PDF 216.006KB
Recall 573 Report- Amendment 1
RCLRPT-20V802-4993.PDF 215.285KB
ISSUED Interim Owner Notification Letter(Part 577)
RIONL-20V802-4746.pdf 90.817KB
Manufacturer Notices(to Dealers,etc)
RCMN-20V802-2601.pdf 630.193KB
ISSUED Interim Owner Notification Letter(Part 577)
RIONL-20V802-3642.pdf 161.567KB
Manufacturer Notices(to Dealers,etc)
RCMN-20V802-3008.pdf 1770.695KB
Manufacturer Notices(to Dealers,etc)
RCMN-20V802-2754.pdf 1478.417KB
Manufacturer Notices(to Dealers,etc)
RCMN-20V802-5543.pdf 1762.549KB
Manufacturer Notices(to Dealers,etc)
RCMN-20V802-4247.pdf 1494.09KB
Latest Recalls Documents
- 【Reset ABS/SRS/Transmission/Engine Lights】 More than an check engine code reader, OBDMATE OM901 obd2 scanner performs comprehensive diagnostics for the 4 most-used systems (ABS/SRS/Engine/Transmission). It quickly clears fault codes, turns off warning lights, read data stream and auto VIN.
- 【3.5" Handheld Scanner with 4 System Diagnose】 3.5" Super large TFT screen equipped displays an intuitive menu and clear readings of various sensors from ABS, SRS, ECM and TCM systems. It arrived with a silicone protective case and hard-shell carrying case, ensuring long-lived durability and drop resistance. The car diagnostic tool is plug-to-play designed, plug it and get diagnosis started without any batteries or updates required.
- 【One-Click I/M Readines&Full OBD2 Functions】 Press F1 to get an intuitive corloured form about whether various emissions-related systems on the vehicle are operating properly. Help you get smog-check ready quickly. OM901 car scanner supports all essential OBD2 functions you need: read & clear codes, view freeze frame, read I/M readiness, retrieve VIN, live data stream (with graphing display), O2 sensor test, onboard monitoring mode, and EVAP leak test.
- 【Battery Voltage Check&DLC Pin Test】 It allows you to monitor battery health by testing current battery voltage. Plus, this obd2 diagnostic tool features DLC 16-PIN test to check current voltage of every pin.
- 【Automotive Scanner Diagnostic Kit】 The package comes with 1 car scanner, 1 USB-type c cable, 1 hard storage bag and 1 user manual(en). Free to update without any hidden fees. 5 languanges available in setting including English, French, Italian, German and Espanish. Valuable and Portable, making it a great tool kit for car owners, DIY enthusiasts, and professional mechanics.
- [Easy to Use—Work Out of the Box] + [FOXWELL 2026 New Version] FOXWELL NT604 Elite scan tool is the 2026 new version from FOXWELL, designed for car owners who want to figure out the cause of issues before fixing car problems by scanning common systems like ABS, SRS, engine, and transmission. The NT604 Elite obd2 scanner diagnostic tool comes with the latest software—no need to waste time downloading software first. Plug the scanner into the OBDII port with OBDII cable to start the diagnosis.
- [Affordable] + [Reliable Car Health Monitor] Will you be confused what happens when the warning light of ABS/SRS/transmission/check engine flashes? Instead of taking your cars to dealership, this FOXWELL scanner will help you do a thorough scanning and detection for your cars and pinpoint the root cause. Note：The device is a diagnostic tool, not a repair tool. To turn off a warning light, you must first physically repair the issue causing it. Only then can the scanner be used to clear the corresponding fault code.
- [5 in 1 Car Diagnostic Scanner] Compared with obd scanners (50-100), NT604 Elite code scanner not only includes their OBDII diagnosis but also serves as ABS/SRS scanner, transmission and check engine code reader. When it’s an odb2 scanner, you can use it to check if your car is ready for annual test through I/M readiness menu. In addition, live data stream, built-in DTC library, data play back and print, all these features are a big plus for it. Note: doesn't support maintenance functions like reset or relearn. For the SRS system, NT604 Elite can read and clear common fault codes not caused by a crash, but crash/collision data cannot be cleared.
- [Fantastic AUTOVIN] + [No extra software fee] Through the AUTOVIN menu, this NT604 Elite car scanner allows you to get your V-IN and vehicle info rapidly, no need to take time to find your V-IN and input one by one. What's more, the NT604 Elite ABS SRS scanner supports 60+ car brands from worldwide (America/Asia/Europe). You don’t need to pay extra software fee. AUTOVIN may not work on some older vehicles or certain vehicle brands. If AUTOVIN fails, please input the vin code manually or go to the Diagnostic Menu to select your vehicle model.
- [Solid protective case KO plastic carrying bag] + [Lifetime update] Almost all same price-level car scanner diagnostic tool only offers plastic bag to hold the scanner.However, NT604 Elite automotive scanner is equipped with solid protective case, preventing your obd2 scanner from damage. Then you don’t need to pay extra money to buy a solid toolbox.
- OBD2 SCANNER FOR ALL SYSTEMS – The INNOVA SD35 is a tablet-based OBD2 scanner designed for advanced diagnostics. Read and clear check engine light, ABS, SRS, and TPMS codes, plus test your car battery and alternator to prevent unexpected failures. Vehicle coverage may vary. Please use Innova’s Coverage Checker to verify compatibility.
- ALL-SYSTEM DIAGNOSTICS & LIVE DATA – Unlike basic code readers, this OBD2 scanner for all vehicles scans engine, transmission, ABS, SRS, and more. Get real-time live data, including RPM, fuel trims, temperature readings, and oxygen sensor performance.
- OBD2 TABLET WITH USER-FRIENDLY INTERFACE – This automotive scan tool features a high-resolution display, making vehicle diagnostics faster and easier.
- ADVANCED TPMS, OIL RESET & SERVICE FUNCTIONS – Perform TPMS sensor checks, oil light reset, and other service resets with ease This professional diagnostic tool provides comprehensive vehicle maintenance capabilities in one device.
- WIDE VEHICLE COVERAGE (1996 & NEWER CARS & TRUCKS) – This OBD2 scanner Bluetooth tablet is compatible with Toyota, Ford, Honda, Chevrolet, Nissan, Dodge, and more. However, feature coverage may vary. Please use Innova's Coverage Checker to verify coverage.
- [All System Diagnostics, Professional-Level Scanner] - BLCKTEC 460T is the ultimate OBD2 diagnostic tool for home mechanics and professionals. It supports all 10 OBD2 modes, reads and clears Engine/Transmission/ABS/SRS codes, performs All-System Diagnostics, offers workshop reset tools, and provides real-time live data. It helps you pinpoint issues, assess your car's condition, and prepare for SMOG checks with ease. NOTE: Function availability depends on your vehicle. Before you buy, be sure to use the Compatibility Checker on BLCKTEC website or contact our customer support to verify that the features you need are supported for your vehicle’s specific year, make, and model.
- [12+ Most Popular Reset Functions] - BLCKTEC 460T OBD2 scanner offers 12+ dealer-level service functions, including Oil Maintenance Reset, ABS Bleeding, EPB Reset, SAS(Steering Angle Sensor) Recalibration, DPF(Diesel Particulate Filter) Reset, Throttle Body Relearn, Battery Reset/Initialization, TPMS Relearn, Transmission Reset, Fluid Change Reset, Maintenance Reset and more, enabling you to perform workshop services like a pro. NOTE: Function availability depends on your vehicle. Be sure to use the Compatibility Checker on BLCKTEC website to verify that the features you need are supported for your vehicle.
- [Real-Time OBD2 and OEM Live Data, Freeze Frame Data] - BLCKTEC 460T helps diagnose vehicle issues when warning lights like Check Engine Light or ABS/SRS Light appear. It offers detailed DTC info, ECU Freeze Frame Data, and real-time OBD2 and advanced OEM live data, including Engine, Transmission, ABS, SRS, and more, making it easy to diagnose and resolve vehicle problems. You can view, graph, record, replay, and overlay up to four live data streams in a single graph for better analysis.
- [AutoVIN, AutoReLink, AutoScan, 3X Faster] - Equipped with AutoVIN technology, 460T automatically retrieves the VIN to save you time. Its AutoScan and AutoReLink features scan all of the vehicle's ECUs and detect any fault codes immediately after you plug the scanner into the vehicle's OBD2 port - no button presses required. Additionally, it regathers DTC and I/M readiness information every 30 seconds, simplifying monitor tests. 460T's advanced technology makes it 3X faster than other products.
- [Get RepairSolutions2, the #1 Auto Repair App for Free] - When paired with RepairSolutions2(RS2) App, 460T becomes even more powerful. RS2's Verified Fix Database built by master technicians, provides the parts needed for the repair. Additionally, RS2 gives you access to OEM warranty info, maintenance schedules, TSB, and dealership recall info, making car care easier than ever. RS2 is free with no subscription fees and it stores your car scan reports in the cloud, allowing you to access, share, or print them anytime and anywhere.
- 【Full Systems Automotive Diagnostic】 More than checking engine, ABS and SRS, OBDMATE OM970 obd2 scanner performs comprehensive diagnostics on all electric modules. It quickly scans and clears fault codes, turns off warning lights, reads live data, and features Auto-VIN technology.
- 【Live Datastream&4-in-1 Graph】 Easily view live sensor data such as RPM, fuel trims, ATF temperature, wheel speed sensor, battery voltage and so on. OM970 scan tool also supports 4-in-1 trend graphing. Spend just 3 minutes to check – and you'll know exactly what's going wrong, helping you avoid hundreds in dealership diagnostic fees.
- 【One-Click I/M Readiness&Full OBD2 Functions】 Press F1 to get an intuitive corloured form about whether your vehicle's emissions-related systems are operating properly. Help you get smog-check ready quickly. OM970 obd2 diagnostic tool supports all essential OBD2 functions you need. Plus, it features battery voltage test and DLC 16-PIN test.
- 【Straightforward Menus with Easy Navigation】 All functions are easy to understand without obscure decriptions. 3.5" Large screen delivers clear readings while keeping one-hand operation. The car diagnostic tool comes with a silicone protective case and a hard-shell carrying case, ensuring long-lived durability and drop resistance.
- 【Budget-Friendly, No Subscriptions, Free Software Updates】 Plug and play: no bluetooth pairing, monthly fees, Wi-Fi connection, or any other troublesome initial settings. OM970 obd2 scanner works out of the box with the latest software. Lifetime free upgrade.
This product presentation was made with AAWP plugin.