BlueTEC Update – 2011-2012 Mercedes-Benz E-Class

“This site contains affiliate links for which OEMDTC may be compensated”
TO: Mercedes-Benz Dealer Principals, General Managers, Sales Managers, Service Managers, Parts Managers FROM:  Gregory Gunther, Department Manager, Vehicle Compliance and Analysis, Engineering Services
RE: Emission Modification Notification – [[2020050028]]  MY11-12 E350 BlueTec Update – Emission Modification Category (EMC) #8 DATE: May 27, 2022

 

IMPORTANT EMISSION MODIFICATION NOTIFICATION

Attention Dealership Management

  • Please ensure that every dealership associate is aware of this Emission Modification notification, and that customer facing associates provide transparent information to Customers.
  • Refer to VMI in NetStar to determine which units in your inventory are affected by this Emission Modification. This notification hereby instructs Dealers not to sell or cause to be sold, or lease or cause to be leased, or introduce into commerce, or export from the United States to another country, any vehicle covered by this notification, unless it has received the Approved Emission Modification described in this notification.  Failure to adhere to these instructions may result in possible penalties or fines.
  • Run a VMI check on all vehicles brought into your Service Department to determine if they are affected by any service campaign or recall and perform accordingly.
  • Always act with the principles of Customer Experience in mind.
  • Refer to the work instructions and ensure each step in the defined process is followed exactly as described. Steps such as affixing the vehicle label and correctly filling out the vehicle label must be adhered to.  Failure to adhere to these instructions may result in possible penalties or fines.
  • Ensure your warranty administrator submits warranty claims for this Emission Modification in a timely manner. Extended warranty applicability stated herein is automatically enabled once the Approved Emission Modification is completed and the warranty claim is processed.
  • A proposed class action settlement has been filed that provides compensation to customers who receive the Emission Modification and meet certain other requirements. To receive such compensation, class members will need to submit (among other things) copies of their Repair Order showing proof that the Emission Modification was installed and (if any) proof of transportation expenses incurred to receive the Emission Modification—up to $35—in the event that a loaner, shuttle, or  alternative transportation cannot be arranged by your dealership.  Please remind customers to save this documentation.
  • Customers should not be given information about the Emission Modification or the class settlement that deviates from, or is in addition to, what is in authorized communications reflected in this NCU or the official websites: https://www.mbbluetecsettlement.com/ and https://bluetecupdate.mbusa.com/home. Failure to adhere to this instruction could threaten final implementation of the settlement and may result in possible penalties.

Other than the benefits class members can claim through the class action settlement process, customers cannot be offered any compensation in exchange for receiving the Emission Modification. Failure to adhere to this instruction may result in possible penalties. (At their discretion and on a case-by-case basis, Dealers can continue to offer customers goodwill for other reasons consistent with normal business practices and policies, but additional compensation in exchange for receiving the Emissions Modification is prohibited.)

 

Information for Customers:

  • For information related to this specific Emission Modification, Customers can refer to:

https://BlueTecUpdate.mbusa.com

  • For information related to the proposed class action settlement, Customers can refer to:

www.mbbluetecsettlement.com

 

Please note that all customer inquiries should be directed to the Customer Assistance Center at 1-833-841-9362.

Sincerely,

Gregory Gunther

Department Manager, Vehicle Compliance & Analysis

 


 

Emission Modification Notification April 7, 2022
Campaign No.: EMC# Campaign Desc. : BlueTEC Update – MY11-12 E (W212)
2020050028 8 19P4992019
This is to notify you of an Emission Modification Notification to update the emission control system on approximately 5700 Model Year (“MY”) 2011-2012 E350 BlueTEC (W212) diesel vehicles.  Emission Modification information will be visible on the https://BlueTecUpdate.mbusa.com website and may generate questions from Owners and Lessees. Affected VINs will be flagged in VMI as “OPEN” on April 7, 2022.
Background
Issue Mercedes-Benz USA, LLC (“MBUSA”) is modifying the emission control system on certain diesel vehicles.  The Emission Modification for MY11-12 E350 BlueTEC (W212) vehicles has been approved by EPA and CARB, and is now ready for installation.  An authorized Mercedes-Benz Dealer will install the Emission Modification at no cost to the Owner/Lessee.
What We’re Doing An authorized Mercedes-Benz Dealer will replace certain emission control system components and update certain software in eligible vehicles.
Parts Parts are available as of 4/7/2022
Vehicles Affected
Vehicle Model Year(s) MY 2011-2012
Vehicle Model E350 BlueTEC (W212)
Vehicle Populations
Total Campaign Population 5700
Total Customer Vehicles in Campaign 5700
Next Steps/Notes
Customer Notification Timeline Customer letters will begin to be mailed on April 7, 2022.
AOMS/SOMS This Emission Modification Notification may initiate questions from customers and the media.  Please ensure your Dealers have read and understand this notice.
Notes
  • IMPORTANT: This notification hereby instructs Dealers not to sell or cause to be sold, or lease or cause to be leased, or introduce into commerce, or export from the United States to another country, any vehicle covered by this notification, unless it has received the Approved Emission Modification described in this notification.  Failure to adhere to these instructions may result in possible penalties or fines.
  • Follow ALL steps of the work instructions.
  • More information about a class action settlement providing incentives to customers who receive the Emission Modification can be found at www.mbbluetecsettlement.com
  • Emission Modification information:

 

While we regret any inconvenience this may cause, MBUSA is determined to maintain a high level of vehicle quality and customer satisfaction. Please refer all customer inquiries to the Customer Assistance Center at 1-833-841-9362.

 


DEALER FAQs

What is the reason for this Emission Modification?

On March 9, 2021, Daimler AG (“DAG”) and Mercedes-Benz USA, LLC (“MBUSA”) reached a settlement with the United States Department of Justice (“DOJ”), the Environmental Protection Agency (“EPA”), the California Air Resources Board (“CARB”), and the California Attorney General’s Office (“CA AG”) regarding the emission control system in MY09 to MY16 OM642 and OM651 BlueTEC II diesel vehicles sold or leased in the US.  As part of this settlement, MBUSA is offering eligible Owners and Lessees a modification to the vehicles’ emission control system, referred to as an Emission Modification.

Eligible vehicles and vehicle model years have been separated into Emission Modification Categories (“EMCs”) to facilitate the Emission Modification Program.  Each EMC will be launched in phases, and MBUSA will notify authorized Mercedes-Benz Dealers after agency approval of each Emission Modification.  Please refer to our public website https://BlueTecUpdate.mbusa.com for more information on your particular vehicle.

 

Is this a recall?

No, this is NOT a recall.  As part of the settlement with the US authorities, DAG and MBUSA are offering eligible vehicle Owners/Lessees a modification to the vehicles’ emission control system, referred to as an Approved Emission Modification (AEM).  This modification will be performed at no cost to the Owner/Lessee.

 

What is an “EMC”?

To facilitate the Emission Modifications on the subject vehicle population, the vehicle models and model years have been separated into Emission Modification Categories.

 

What are the eligible vehicles that will receive an Emission Modification under this settlement?

This settlement pertains specifically to MY09 to MY16 BlueTEC II diesel vehicles with OM642 and OM651 engines sold or leased in the US.  For more information, please visit https://BlueTecUpdate.mbusa.com.

 

How will the Emission Modification be communicated to Owners and Lessees in the US?

Owners/Lessees will first receive a letter in the mail indicating that the Emission Modification is available for their vehicle and inviting them to schedule an appointment with their preferred authorized Mercedes-Benz Dealer.

 

How do Owners and Lessees find out whether their vehicle is affected by the Emission Modification Campaign?

Owners and Lessees with affected vehicles will be mailed a notification letter when the Emission Modification is available.  Owners and Lessees can also check if their vehicle is affected by entering their VIN into the following site:

https://BlueTecUpdate.mbusa.com.

All vehicles covered by the Emission Modification Program also are covered by the proposed class action settlement described herein.

 

Owners and Lessees might complain about a Check Engine light; will the Dealer repair the vehicle as part of the emissions update?

A Check Engine light can illuminate for a number of reasons.  Authorized Mercedes-Benz Dealers can offer assistance diagnosing and repairing the issue.

 

Can an Owner or Lessee get a loaner vehicle or alternate transportation while the Emission Modification is being performed?

Where loaner vehicles are available, Dealers are requested to offer loaner vehicles to each Eligible Owner and Eligible Lessee at no cost where the implementation of the Approved Emission Modification will take 3 hours or longer to complete.

In an instance where the Approved Emission Modification takes 3 hours or longer to complete, and where the Dealer does not make available a loaner car or offer a shuttle service or alternative transportation, Class Members will be eligible to submit a claim for transportation costs of up to $35 along with their claims for other settlement compensation.  For more information on the transportation allowance, customers should visit the class action settlement website at www.mbbluetecsettlement.com, and should be reminded to save their receipts.

 

What is Mercedes-Benz going to do for Owners and Lessees given this inconvenience?

Dealers will attempt to minimize any inconvenience during the Emission Modification process.  Should Owners or Lessees experience an excessive delay with the Emission Modification of their vehicle, they can contact our Customer Assistance Center at 1-833-841-9362.

As part of the proposed consumer class action resolution, current owners and lessees of eligible vehicles who go to authorized Mercedes-Benz Dealers, have an Approved Emission Modification installed, and meet certain other requirements will be eligible to claim a payment of up to $3,590.  For more information on eligibility and the process for filing a claim, customers should call the number above or visit the class action settlement website at www.mbbluetecsettlement.com.

 Other than the benefits that class members can claim through the class action settlement process, customers cannot be offered any compensation in exchange for receiving the Emission Modification.  Failure to adhere to this instruction may result in possible penalties.  At their discretion and on a case-by-case basis, Dealers can continue to offer customers goodwill for other reasons consistent with normal business practices and policies, but additional compensation in exchange for receiving the Emission Modification is prohibited.

 

Where can an Owner or Lessee have the Emission Modification work completed?

Owners and Lessees will be asked to contact their local preferred authorized Mercedes-Benz Dealer to arrange for an appointment to complete the FREE Emission Modification.

 

Can Owners and Lessees have the Emission Modification performed if they did not receive a Notification Letter in the mail but own a Mercedes-Benz BlueTEC diesel vehicle? 

Owners and Lessees should first check the eligibility and status of their vehicle by visiting https://BlueTecUpdate.mbusa.com.  To be automatically alerted when the Emission Modification is available for their vehicle, Owners and Lessees are being asked to complete the “Keep me Updated” section of the website after entering their VIN to check the status.

 

Do Owners and Lessees have to wait for the notification letter in the mail before their vehicle can receive the Emissions Modification?

Owners and Lessees do not need to present a copy of the notification letter to receive the FREE Emission Modification, but they should wait to bring their vehicle in for the Emission Modification until they receive notice that the Emission Modification has been launched for their specific vehicle model.  The Emission Modifications will be launched in phases, pending agency approval, so the Emission Modifications for all of the subject vehicle models (all MY09 to MY16 BlueTEC II diesel vehicles with OM642 and OM651 engines sold or leased in the US) will not be launched at the same time.  Once the Emission Modification has been approved for a particular vehicle type, Owners and Lessees will be sent a letter asking them to schedule an appointment with their authorized Mercedes-Benz Dealer to perform the FREE Emission Modification.

 

Do Owners or Lessees need the Owner/Lessee notification letter to have the Emission Modification performed?

No, Owners and Lessees with eligible vehicles do not need the notification letter to have the FREE Emission Modification completed.  Local authorized Mercedes-Benz Dealers can check the eligibility and status of vehicles without the letter.

 

What about Owners or Lessees who request that the Emission Modification be performed without first receiving a letter?

No Emission Modification can be performed until EPA and CARB approve the Emission Modification for the specific model. Similarly, the affected VIN must be flagged as “OPEN” in VMI with the respective Emission Modification campaign number for the modification to be performed.

 

When will parts be available?

Parts are currently available for the Emission Modifications which have been approved by EPA and CARB.  We will provide updates as parts become available for other vehicle models.

Regarding all other future vehicle categories, MBUSA is working with EPA and CARB to obtain approvals for the Emission Modification.  MBUSA will notify Dealers upon approval of each Emission Modification that the Emission Modification has become available.

For up-to-date parts availability information, please refer to the website https://BlueTecUpdate.mbusa.com.

 

Are there any known vehicle symptoms associated with the Emission Modification that Owners or Lessees will notice that should lead them to stop driving or take their vehicle to a Dealer?

No.  There are no symptoms related to the Emission Modification.

 

What is the expected impact on an Owner’s or Lessee’s vehicle after the Emission Modification has been performed?

Details on the impact to vehicles are provided in the letter for each Emission Modification Category.  A copy of the Owner/Lessee letter for the EMC subject to this FAQ is attached.

 

What types of repairs or replacements are needed?

Authorized Mercedes-Benz Dealers will replace specific emissions-related components.  This varies by model and model year.  For more information, please visit https://BlueTecUpdate.mbusa.com.

 

How long does this Emission Modification take?

Replacement time is dependent upon the model and model year.  This time may range from 30 minutes to a maximum of 13.0 hours.  Details are provided in the Owner/Lessee notification letter.

 

What if vehicles have been modified using after-market parts and/or software? Can the Emission Modification still be performed?

If, prior to receiving the Emission Modification, the vehicle has been modified in a manner that impedes the installation of the AEM or substantially affects the operation of the AEM after install (for example, removal of original emissions components not part of the AEM), dealers might not be able to perform the Emission Modification until the prior modifications are corrected.  The Owners/Lessees would be responsible for such corrections.  Once corrected, the vehicle may receive the Emission Modification.

 

What if Owners or Lessees decline to have the Emission Modification performed?

If Owners/Lessees decline the Emission Modification at this time, they will be advised by their authorized Mercedes-Benz Dealer that certain emissions-related replacement and repair parts (for their existing system) may no longer be available from Mercedes-Benz at some point in the future.  Additionally, the current vehicle Owner/Lessee will not be able to make a compensation claim as part of the proposed class action settlement without first having the Emission Modification performed on their vehicle.

 

Will eligible vehicles have any warranty on the Emission Modification?

Yes.  Once the Emission Modification is performed, certain components will have an extended warranty for the greater of 4 years/48,000 miles from the date of installation of the Emission Modification or 10 years/120,000 miles from the initial sale date of the vehicle.  As described in the Customer Letter, some emission-related components have an additional extended warranty period, which is added to the applicable Extended Modification Warranty period above.  This extended warranty remains with the vehicle and is fully transferable to subsequent owners until expiration.  Where loaner vehicles are available, Dealers are requested to offer loaner vehicles to each Eligible Owner and Eligible Lessee at no cost where extended warranty repairs exceed three hours to complete.

 

Can Owners or Lessees be denied coverage under the Extended Warranty for the Emission Modification?

The Extended Warranty for the Emission Modification may be denied if an eligible vehicle has been altered with the use of any after-market emissions-related components, parts, and/or software, or with the removal of any original emissions-related components, parts, and/or software, and such alteration(s) are likely to substantially affect the operation of the vehicle with the Emission Modifications, until the owner of such vehicle, at his or her expense, has reversed the alteration(s) such that the Emission Modification will not be substantially affected.

 


 

Campaign No. 2020050028, April 2022

 

TO: ALL MERCEDES-BENZ CENTERS
SUBJECT: Model E-Class diesel vehicles (W212 platform)
Model Year 2011-2012
Modification to the emission control system

 

Mercedes-Benz USA, LLC (“MBUSA”) is performing an emission campaign on certain MY11-12 E-Class (W212) diesel vehicles in order to modify the vehicles’ emission control system. EPA and CARB have approved this emission modification. An authorized Mercedes-Benz dealer will replace certain emission control system components and update certain software in the affected vehicles at no cost to the owner of the vehicle.

 

Prior to performing this Emission Campaign:

  • Please check VMI to determine if the vehicle is involved in the emission modification campaign and if it has been previously repaired. Always Check VMI for any open campaigns, and perform accordingly.
  • Please review the entire Emission Campaign bulletin and follow the repair procedure exactly as described.

 

Approximately 5,700 vehicles are involved.

 

Order No. P-EC-2020050028

 


Scope of Work: 

Note: Videos of exemplary modifications of a GLK250  BlueTec (MY13) and a ML350 BlueTec (MY12) can be found on WIS Service Media (WSM): GLK250 BlueTec: WSM ⇒ Content by model series ⇒ Passenger Cars ⇒ GLK (Model 204.9) ⇒ 49 – Exhaust system

 

Work procedure 

  1. Connect XENTRY and perform Initial Short Test and Pre-Inspection
  2. Disconnect Battery Ground
  3. Replace charge air distribution line right and left, charge air cross-pipe, clean air pipe, EGR valve, EGR cooler and exhaust pipes.
  4. Replace the changeover flap
  5. Replace components of the exhaust system (DPF/DOC and SCR catalyst).
  6. Remove the O2 sensor
  7. Install plug for oxygen sensor port in DPF filter
  8. Install plug housing to O2 sensor on the electrical harness
  9. Replace both NOx sensors
  10. Connect the ground line of the battery
  11. Connect XENTRY Diagnosis.
  12. Update and commission the engine control unit, update the software of the engine control unit, VGS and SCR.
  13. Replace the engine control unit
  14. Attach the adhesive label
  15. Complete XENTRY Diagnosis.
  16. Perform a final quick test

 

Parts Overview

 

Procedure

 

  1. Initial Short Test and Initial pre-inspection

 

1.2  Connect XENTRY diagnosis.

Note:

  • Use DAS/XENTRY 09/21 with all associated patches or higher.
  • Follow the steps exactly as described in DAS/XENTRY.
  • Ensure all electrical consumers are switched-off.
  • In the event of software/SCN update issues, contact Star Diagnosis User Help Desk. Please refer to the “pre-call” check list before contacting UHD
  • Refer to Star Diagnosis System (SDS) Best Practices Guide.

 

1.3 Perform Pre-Inspection

Follow the XENTRY procedure “Emission Modification Pre-Inspection”: “Main groups ⇒ Control units ⇒ N3/9 CDI 6-Common Rail Diesel Injection ⇒ Special procedures ⇒ Service measure “Exhaust aftertreatment system” ⇒ Pre-Inspection

 

Record findings on workorder and save to paperless

Note: goal of the pre-inspection process is to perform an inspection of the emission system and ensure all components are present and functioning correctly (Check engine light “CEL” ON/OFF).  The pre-inspection consists of the following procedures as displayed in the below flowchart:

 

  1. Visual inspection of the emissions system to check for non-compliant alterations to the emission system that impedes the installation of the Approved Emission Modification (AEM) or substantially effects the operation of the AEM after installation. This consists of a brief visual inspection and does not require a technician to confirm if components are operating correctly. (Example: missing emission system components not replaced as part of the AEM)

1.1 If an alteration has been found during the visual inspection that meet the criteria mentioned in point 1, please advise the customer these alterations must be reversed at their expense before to proceed with the AEM.  Please follow the below process to submit a warranty claim for the time associated to diagnosis and provide an estimate to the customer.

Warranty Documentation Process:

    1. Claim against damage code 4910N 01 – Approved Emission Modification Denial
    2. Up to 2 hours of diagnostic time permitted
    3. Ensure diagnostic time is properly punched on the RO
    4. Ensure RO is documented properly including a detailed explanation as to why the modification was denied
    5. Attach the RO to the warranty claim

 

  1. Initial Short Test to check for CEL ON/OFF: Pre-existing issues (CEL ON) may be addressed at the time of AEM install if the components diagnosed are part of the AEM or extended warranty. For all other components, please provide the customer with a repair estimate and document if the customer approves/declines the additional repair(s).  It is essential the AEM is installed regardless if the customer approved/declines additional repairs to address a pre-existing issue.  A list of applicable extended warranty parts is available in XENTRY for the technician to refer to.

 

1.4 Pre-Inspection Overview (Figure 1)

 

1.5 Disconect XENTRY diagnosis and remove battery charger

 

  1. Disconnect battery ground.

For basic data, see AR54.10-P-0003EW.

 

  1. Replace the charge air distribution line on the right (A 642 090 06 37) and left (A 642 090 70 37), charge air crosspipe (A 642 090 16 37), clean air pipe (A 642 090 82 37), EGR valve (A 642 140 19 60), EGR cooler (A 642 140 23 75) and exhaust pipes (exhaust pipe front (A642 140 34 08),  exhaust gas recirculation pipe (A 642 140 29 08), exhaust pipe/discharge (A 642 140 27 08)).

For basic data, see AR14.20-P-7665SXI.

SI01.10-P-0004A.

The coolant is to be used again! The coolant must be drained, collected in a clean container and reused.

If possible, do not loosen the oil leak line, as it is quickly damaged.  It is better to disconnect the lines on the fuel filter.

If the oil leak line needs to be loosened, absolute caution should be exercised.

The corresponding spare parts are listed in the parts table under the respective spare part!

Tighten the screw of the adjusting motor ( 5) (Figure 2) (A 642 450 05 94), only after the charge air distribution line has been installed.

Replace the O-rings (A 000 078 05 80) of the oil leak line at the injectors (Figure 3).

 

The line that runs from the left fuel distributor to the right fuel distributor is replaced by a new version (A 642 070 09 00) (Figure 4).

 

For position 1, Figure 4, use the new clamp (N 000000 006288) and new screw (N 000000 001116 M6x19mm).

 

For position 2, Figure 4, reuse the old clamp and new screw (N 000000 001114 M6x15mm).  The old clamp must be reinstalled as shown. Attention must be paid to abrasion-free installation.

 

  1. Replace the changeover flap (A 642 140 14 63).

For basic data, see AR14.20-P-7661CD.

 

  1. Replace components of the exhaust system (DPF (A 212 490 78 00 85), DOC (A 212 490 77 00 85), and SCR (A 212 490 50 00 80)).

For basic data see AR49.10-P-7100EWI, AR14.40-P-1000OGE, AR49.10-P-5500OGE.

All stickers on the DPF/DOC unit and SCR catalyst must be removed.

 

  1. Remove the O2 sensor.

For basic data see AR07.04-P-0080OGE.

 

  1. Install screw plug (N 007 604 018 109) and sealing ring (A 021 997 62 45) for the O2 sensor port on the DPF

 

  1. Install the plug housing (A 000 545 40 39) on the electrical connection for the O2 sensor (Figure 6).

The electrical connection of the O2  sensor is no longer needed!

 

  1. Replace both NOx sensors (A 642 905 11 00 85).

For basic data, see AR14.40-P-2038OGE.

NOx sensor upstream of SCR catalyst (A 000 905 56 12 80)

NOx sensor downstream of SCR catalyst (A 000 905 57 12 80).

It is not necessary to perform the reset routine with XENTRY Diagnosis.

The new sensors are already equipped with hot lubricating paste.

The wires on the old NOx sensors should be cut off to facilitate removal and to ensure that they are not reused (Figure 7).

 

  1. Connect the ground line of the battery.

For basic data, see AR54.10-P-0003EW.

 

  1. Connect XENTRY Diagnosis.

 

  1. Update and commission the engine control unit, update the software of the engine control unit, VGS and SCR.

To do so, select menu item “Control units view ⇒ N3/9 – CDI 6-Common Rail Diesel Injection ⇒ Special procedures ⇒ Service measure “Exhaust aftertreatment system” ⇒ Perform Service Measure “Exhaust aftertreatment system”.

Then follow the user guidance in XENTRY Diagnosis.

In the background, additional control units may be automatically updated.

 

  1. Replace the engine control unit (A 642 900 98 01).

For basic data see AR07.08-P-7008OGE.

 

The commissioning of the new control unit is started automatically.

 

  1. Clean the bonding surface area of the hood and apply the adhesive label (A 000 584 65 15) (Figure 8).

The fields on the label must be filled in accordingly.  Please use black permanent marker.  Refer to XENTRY procedure.

The adhesive label can be attached to the hood during the software update of the control units.

 

  1. Complete XENTRY Diagnosis.

 

  1. Perform a final quick test and transmit to paperless SDS.

Faults stored in the memory, caused by disconnected lines during the inspections, must be deleted from the fault memory after completing the work.

If faults are present they need to be addressed. Create a PTSS case if technical support is needed.

 

Primary Parts Information

Qty. Part Name Part Number
1 Part kit (2 x NOX sensors) A 642 905 11 00 85
1 Part kit (DOC) A 212 490 77 00 85
1 Parts kit (DPF) A 212 490 78 00 85
1 SCR catalyst A 212 490 50 00 80
1 Engine control unit A 642 900 98 01
1 Profile sealing ring A 021 997 62 45
1 Screw plug A 094 990 18 08
1 Plug housing A 000 545 40 39
1 Adhesive label A 000 584 65 15
1 Part kit charge air pipe left A 642 090 26 00
1 Part kit charge air pipe right A 642 090 27 00
1 Part kit charge air cross pipe A 642 090 23 00
1 Hexagon nut charge air cross pipe A 000 990 43 37
1 Clean air pipe A 642 090 82 37
1 Bleed valve kit A 642 010 74 15
1 Parts set EGR cooler A 642 140 07 00
1 EGR valve A 642 140 19 60
2 Screw N 000000 001117
1 Exhaust pipe front A 642 140 34 08
2 Screw N 910143 006001
1 Exhaust gas recirculation pipe A 642 140 29 08
1 Screw N 000000 001116
2 Screw (M6x55) N 910105 006014
1 Gasket A 642 142 11 81
1 Part kit exhaust pipe / discharge A 642 141 06 00
1 Changeover flap A 642 140 14 63
1 Parts kit exhaust gas turbochargers A 642 140 08 00
1 Parts kit small Parts Fuel Supply A 642 070 16 00

Small parts such as screws, stop nuts, sealing rings, cable ties, liquids, sealants, etc. are not listed in the parts listing. The required small parts are within budge taken into account.

Parts listed below bolded parts are included in the same repair step

 

Warranty Information

Operation: (02-1088) Replace NOx sensors and exhaust system components

Includes: Replace charge air distributor line right and left, charge air cross-pipe, clean air pipe, bleed valve, EGR valve, EGR cooler and exhaust pipes (exhaust pipe front, exhaust gas recirculation pipe, exhaust pipe/discharge), changeover flap, replace DPF/DOC and SCR catalyst, remove and cap O2 sensor port, attach adhesive label to the hood, disconnect and connect the ground line of the battery, XENTRY Diagnosis, replace engine control unit, commissioning of the engine control unit

Damage Code Operation Number Labor Time (hrs.)
49 920 19 02-1088 13.0

Note

Operation labor times are subject to change

 

P-EC-2020050028

 


Launch NCU – EMC 8 – MY11-12 W212 BlueTEC Update

https://www.startekinfo.com/service/download-document/outside/226413/

https://static.oemdtc.com/Recall/S-EC-2020050028May2022.pdf

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [2.16 MB]

 


Launch NCU – EMC 8 – MY11-12 W212 BlueTEC Update

https://www.startekinfo.com/service/download-document/outside/226413/

https://static.oemdtc.com/Recall/P-EC-2020050028.pdf

Loader Loading...
EAD Logo Taking too long?

Reload Reload document
| Open Open in new tab

Download [1.99 MB]

 


 

Mercedes-Benz Reprogramming

J2534 Pass-Thru

All information in regard to Mercedes-Benz J2534 compliant software is available free of charge and found under the MB Workshop Resources tab on the home page of www.startekinfo.com

J2534 complaint software for Mercedes-Benz vehicles is available for purchase from Mercedes-Benz USA.

In order to use the J2534 complaint software for Mercedes-Benz vehicles, the purchaser must furnish their own:

  • Windows based PC or laptop*
  • J2534 compliant interface box*1*

*Must be purchased from a third party company and are not available from Mercedes-Benz USA LLC.

*1* suggested listing of J2534 interface boxes is located within the J2534 Pass-Thru User’s Manual which is posted for view without cost under the MB Workshop Resources tab on the home page of www.startekinfo.com

 

Vehicle Coverage

J2534 complaint software for Mercedes-Benz vehicles has coverage for all required functions associated to reprogramming, initialization, and fault clearing of emission control modules (engine and transmission) fitted to vehicles 2004 Model Year and newer. Additionally all access and functionality required in regard the configuration via SCN Coding and/or CVN Coding is covered.

J2534 complaint software for Mercedes-Benz vehicles is delivered via DVD media which is delivered monthly for the license term of one year upon purchase.

  • All control unit software (reprogramming calibrations) is contained within J2534 DVD media.

 

Terms and conditions

J2534 complaint software for Mercedes-Benz vehicles is purchased in 1-year license increments. During that license term the user will receive an initial software package, license key, SCN/CVN Coding information/access as well as monthly updates via DVD media.

  • Additional updates of software after the 1st year can be purchased at additional cost, however are not required for the system to continue functioning.

For pricing and additional information via the internet, please refer to the information at the beginning of this section.

 

BlueTEC Update - 2011-2012 Mercedes-Benz E-Class | small light CarDAQ-Plus - PassThru J2534 Vehicle Reflash Hardware
BlueTEC Update - 2011-2012 Mercedes-Benz E-Class | small light CarDAQ-M Modular PassThru J2534 Vehicle Reflash Hardware
BlueTEC Update - 2011-2012 Mercedes-Benz E-Class | small light CarDAQ-Plus 3
BlueTEC Update - 2011-2012 Mercedes-Benz E-Class | small light Bosch Automotive Tools MTECH2 Mastertech II J2534
BlueTEC Update - 2011-2012 Mercedes-Benz E-Class | small light Autel (AULMF2534) MaxiFlash Pro
BlueTEC Update - 2011-2012 Mercedes-Benz E-Class | small light Drew Technologies (DRWCDPLUSKIT) CarDAQ-Plus J2534 Flash Reprogramming Kit
BlueTEC Update - 2011-2012 Mercedes-Benz E-Class | small light RAP2 OEM J2534 Remote Reprogramming Tool
BlueTEC Update - 2011-2012 Mercedes-Benz E-Class | small light Autel MaxiFlash Elite VCI J2534 Pass-Thru ECU Programming Tool
BlueTEC Update - 2011-2012 Mercedes-Benz E-Class | small light BOSCH Automotive Tools MTECH2 Mastertech II J2534 VCI
BlueTEC Update - 2011-2012 Mercedes-Benz E-Class | small light Autel MaxiFlash VCI Vehicle Communication Interface J2534 PassThru ECU Programming Device Bluetooth Connection Internet Update Support CAN FD, 4 CAN Channels, DoIP, D-PDU Works with PC or Autel MS909
BlueTEC Update - 2011-2012 Mercedes-Benz E-Class | small light GODIAG J2534

 

www.startekinfo.com

 


 

Bestseller No. 1
CarDAQ-Plus 3 All Makes J2534 Reprogramming Tool
  • ALL OF THE J2534 PROTOCOLS - This single unit has all of the protocols you need for your OEM J2534 reprogramming and diagnostics including the latest in DoIP and CanFD
  • J2534 TECHNICAL SUPPORT - FREE for the life of the tool. Staffed by technicians who understand vehicle repair and J2534 Pass‑thru
  • TOOLBOX WITH OEM APPLICATION DESCRIPTIONS - educational video tutorials and real-time news – Giving you the confidence and up-to-date knowledge to get the job done
  • J2534 v05.00 API - The newest version of J2534 to give you the latest in pass-thru technology
  • FUTURE PROOF WITH 4 CAN CHANNELS - Going beyond the 3 required by select Chrysler/FCA models, CarDAQ-Plus 3 also provides a 4th to meet the needs of future OEM applications
Bestseller No. 2
VNCI J2534 for Nano Diagnostic Tools,Support J2534 for Automatic Switch Mode Fast Communication
  • Application:Support most all of J2534 compatible software, most all of for software, ECU reprogramming in J2534 mode with programming voltage, supply software for diagnosing J1979 compatible vehicles.
  • Material:VNCI (Vehicle network communication interface) is a device that works between diagnostic software and vehicle. It is compatible with J2534 Passthru and for .
  • Advantage:Support J2534 and for mode in one device, and has automatic switch mode, more speedup, faster communication and reprogramming.VNCI J2534 for Nano protocol configuration include, for ISO15765, for ISO9141, for ISO14230, for J1850 PWM( supports IFR and 2X speed modes), for J1850 VPW (supports 4x speed mode).
  • Easy to install:More stability, never let you down while reprogramming, portable and convenient, small package and easy to carry.
  • Best Experience :We strive to provide you with the best quality products and the best customer experience.We try our best to meet your requirements.Please check the product information carefuly berore buying to aviod making mistakes.
Bestseller No. 3
LAUNCH X431 PRO5 Elite,J2534 Reprogramming Tool, Topology Mapping OBD2 Scanner Diagnostic Tool, CAN/CAFD/DoIP/HD/FCA SGW,Bidirectional Scan Tool, ECU Coding, 50+ Reset, All Systems Scanner
  • 🆚LAUNCH X431 PRO5 scan tool Upgrade all functions of X431 PRO3/X-431 Throttle III/X431-TorqueIII/X431 V+, PROS V+, PAD3. ⓵ J2534 ECU Programming &Online functions directly connect to OEM server, 50+ reset same as X-431 Throttle;⓶Bi-directional control and All system diagnostics as Snap-on scanner; ⓷ Support 150+ brands Vehicles (include CAN/CAFD/DoIP/HD protocols and AutoAuth for FCA SGW) ⓸Powered by 8-core processor(1.8GHz), Android9.0 OS, 2.4 & 5GHz WiFi connection.
  • 🚜[J2534 Reprogramming With FREE SMARTBOX 3.0】Save more than $2000, LAUNCH X431 PRO5 support J2534/DOIP/CANFD/HD protocols (Needn’t buy HDIII Module,Manufacture software and non-16pin adaptors need to be purchased separately.) Download OEM software from the manufacturer’s server to 1) program data to blank/used ECUs; 2) Reflash ECUs with data loss; 3)Upgrade ECU software version. As a wireless VCI allowing the vehicle to transmit data to the diagnostic tablet without a physical connection.
  • 👏[50+ Reset, Continuously Updated Reset Functions]: With the LAUNCH diagnostic tool, You will never be bothered by tricky vehicle issues and keep pace with newer technology. 50 commonly reset functions ( in the quick page ) reaching into the smallest parts to root out the problems. Extra 300+ repair functions ( in-vehicle catalog) for specific models extend the capability to reset, regeneration, initiation, matching, etc. (Functions vary by models, configurations, and systems.)
  • 🌐[One stop Intelligent Diagnostic Tool]: LAUNCH X431 PRO5 obd2 scanner Bluetooth provides Repair Tips, Repair Assist, Component Measurement, TSB, Relevant Cases DTC Analysis to simplify complex diagnostic and achieve the trouble-free repair. 🤩[One Scanner For Multiple Uses]: LAUNCH diagnostic tool PRO5 collaborates with add-on modules (ADAS, Videoscope, TSGUN, X-ProG3, WiFi Pinter, Battery Tester) to expand business applications and improve diagnostic accuracy.
  • 👍【2024 New OE Level Online Functions 】Bidirectional Scan Tool offers you various high-end online functions, which enable you to access the online data to do fast & complicated vehicle repairs, e.g. 1) ECU Coding for replacing, match, relearn, recode new ECU modules; 2) Online Coding for BMW, Audi, VW, Porsche, Benz to surf OEM data; 3) VAG Guided functions ease complex issues; 4) Personalization & ADAS improving car performance and driving safety.
Bestseller No. 4
Autel MaxiFlash Elite VCI J2534 Pass-Thru ECU Programming Tool, Multi-Protocol PassThru Interface, Work with Autel MaxiSYS Elite II, Elite, MS908, MS908S Pro, MS908CV, MK908P, MK908 Pro II and PC
  • 🌐【Works with Autel MK908, MS908(S/Pro), MK908P, MaxiSys Elite】Autel J2534 work with these tools to program ECUs on specific BMW/ BENZ for specific functions. ★★NOTE: J2534 CANNOT directly work with these single devices. After you received the J2534, you HAVE TO send us both the S/N(12 digits) of your scanner MS908S(etc.) and J2534. So, technically, Autel engineers can help you bind J2534 with your devices. If need any supports, contact us via: 🚘auteldirect @ outlook. com🚘.
  • 🌐【SAE J2534-1 & J2534-2 Standards】Autel MaxiFlash Elite J2534 is a fully compliant SAE J2534-1 & SAE J2534-2 (March 2006) device, which performs standard PassThru J2534 functionality: Compatible with for Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. Autel MaxiFlash J2534 is also specially designed to provide users with P-C communication and ECU reprogramming capabilities on any modern vehicle diagnostic bus, reliability and flexibility.
  • 🌐【High-speed Transmission Speed】Autel MaxiFlash Elite Reprogramming Device J2534 supports simultaneous communication definition in J2534-1, running 3 protocols at the same time, which greatly improves reprogramming and diagnostic speed. Embedded with the ARM9 Dual-core processor (clocked up to 500MHz), which further boosts the communicating speed to save more times and win more business.
  • 🌐【Multiple Devices Connected with PC】Autel MaxiFlash Elite J2534 also supports multiple device connections to the PC, which can operate diagnostic and reprogramming functions on more than one vehicle at the same time. Autel MaxiFlash Elite J2534 built-in wireless and data storage, which can update via Internet. It also ensures quickly reprogramming even the newest controllers.
  • 🌐【Extensive Compatibility】Autel MaxiFlash J2534 is compatible with Toyota Techstream, Volvo VIDA, Honda HDS, Jaguar-Land Rover IDS and BMW 3G for OEM diagnostics. To check compatibility, please contact 🚘auteldirect @ outlook . com🚘 directly for satisfaction-guaranteed support!
Bestseller No. 5
Mongoose-Plus J2534 OEM Vehicle Interface Cable - GM OEM Reprogramming and Diagnostics
  • Industry-leading J2534 Pass-Thru Technology: Enabling diagnostics, reprogramming and security functions for dealerships and the independent repair facility. Economical and compact pass-thru devices provides an easy-to-use interface that allows you to repair complex vehicles with OE applications in your shop. Each type (see single branded types above) Mongoose-Plus is engineered to work with one of the following OEM's J2534 applications for Chrysler, Ford, GM, Nissan, Toyota, Subaru, & VW/Audi.
  • Supports Current GM Vehicles: Now includes CAN-FD, DoIP (Diagnostics over Internet Protocol - as defined in J2534-2) and support for J2534 version 5.0. This is the tool that GM dealerships use for diagnostics and reprogramming.
  • NEW Bluetooth Wireless Options Available: Providing wireless connectivity between your laptop and the Mongoose-Plus
  • Expert Product Support: Staffed by technicians who understand vehicle repair and J2534 Pass‑Thru applications to help you with any technical setup questions
  • Key Registration and Immobilizer Support: Using NASTF Vehicle Security Professional credentials
Bestseller No. 6
VXDIAG VCX Nano GDS2 and Tech2Win Diagnostic Tool Compatible for GM/OPEL with Global Diagnostic Programming System GDS & GDS2 Blue
  • 🚗[Technical assistance] If you have any installation problems, download the installation manual. Or please contact us at any time. We can provide technical support and help you install software online
  • 🚗[Vehicle Coverage] Installation Tips: Please turn off anti-virus software before install. VXDIAG VCX NANO fully compatible with SAE-J2534-1 & SAE-J2534-2. All current and most legacy vehicle protocols: CAN, UART, KW2000, Class2, GM LAN, etc.
  • 🚗[Functional] ●USB vehicle-to-PC connectivity●Supports Windows,XP●CE and FCC compliance for hardware●Firmware Updatable. 【SPS】Service Programming System: ◎Passthrough programming on GM past model and Global A vehicles◎Increase reprogramming speed 20-70% and get ready to service new models.
  • 🚗[GDS] Global Diagnostic System: ◎New Diagnostic Application Software required for all GM Global Architecture (Global A) Vehicles. ◎GDS & GDS2 is software which runs on a specific PC. Updates received via TIS2Web.
  • 🚗[Efficient&Convenience] Quick access to vehicle data for maintenance or management reports.Quickly attaches to vehicle's diagnostic connector. Mixed fleet capabilities with broad protocol support.May be used with desktop PC or laptop. make sure your computer at least 4GB.Tech2win software only installed on 7 32bit computer and on physical system.Please download the latest vxmanager from vxdiag official website.

Last update on 2024-03-18 / Affiliate links / Images from Amazon Product Advertising API

This product presentation was made with AAWP plugin.

Leave a Comment

Share to...